Carbhub WT-875 Carburetor for Craftsman Poulan Pro Blower BVM200C BVM200VS P200C GBV325 P325 with Fuel Line Filter Gasket Spark Plug Replace 545081855 WT-875 WT-875A

I bought this carburetor with great hope. My old Craftsman 25cc blower refuses to restart unless it sits for several hours to get thoroughly cold. (and it's not an ignition issue) This carburetor is even worse than the original. THIS carbuiretor isn't even made the same as the original. The jet needle and aperture for the high speed jet are the same size as those for the idle jet. They _should be_ rather larger, as one can see by examining the original. That in turn makes it impossible to adjust the jets for running the blower. (the jets trade off between each other because the flow rates are the same) Even the jet outlet openings in the venturi are located differently than in the original. Even worse, the throttle plate was mislocated so that the idle air slot is away from the idle jet opening. (by 30 degrees or so) Worst of all there were metal filings inside the fuel passages, which I found in using Gumout to spray through them for cleaning. I have yet to find jet settings that work even after the cleaning.EDIT: The one saving grace for this carb is that I was able to cannibalize various parts from it (the inlet chamber cover along with its primer check valve, diaphragm and gasket) to refurbish the older carb. [Walbro WT-875A] By discarding THIS CARB and using the cannibalized parts I was able to fix the trouble with my blower. There's no telling how long that will last.I'd say that someone wanted to sabotage a blower that one might wish to repair so as to force purchase of a new one. Junk.

Used to replace my stock carb on a poulan blower. Now, take NOTE OF THIS: if you are having tuning issues, such as, the carb going out of tune fairly quickly (within minutes) or perhaps even a bit longer, check that the High or Low needle are not freely moving when the engine is running due to vibrations!!!.At first, the carb worked great, then over time, it started performing poorly, I would adjust it and it would work great for maybe a minute then would go out of tune. I re-tuned it a few time and then, I could feel that the High needle was very loose. I actually watch it turn itself as the engine was running due to vibration.I Solved the issue by using a small oring (I'm a hotrod/car guy so I have plenty of those for holley carb etc) which fit over the threads and into the cavity where the needle sit. Effectively, it is now preventing the engine vibration from rotating it. I suppose one could use a drop of lock tight, let it sit over night and then it would accomplish the same thing: give it snug fit.Now the carb is working flawlessly, and stays tune weeks after weeksDespite that little "issue" I feel this is 5 stars as I think this a pretty unique and even rare issue

This carburetor fit exactly like the old one and gave new life to an old leaf blower. Not like some of the other sellers it came with the right adjustment tool for the carburetor. After installing took roughly 10 minutes a crank up on the second pull ran like a champ the only thing I did was adjust the high speed screw just a tad and adjusted the idle speed, great power now. I definitely recommend buying from this seller has everything listed is the correct parts for that particular carburetor.

Amazing! Haven’t used my Craftsman Leaf Blower in years because I didn’t want to pay what it might cost to repair it. Then I was told it’s probably a carburetor gone bad. I Youtubed it and confirmed it. I immediately ordered this and was awed. It took me 20 min start to finish to remove and replace. Started right up on 2-3 pulls of rope. It comes with everything you need from spark plug to fuel lines and filter! I highly recommend!

Having a little problem with idling its starts but you have to put it on full run there is no medium, at least it run. I tried adjust it but not good at it. This the second time I've ordered it this carb, the first one I couldn't get it to idle at all and put my old back on and lived with it ,until now so I order another one at least it runs. This goes on a Bolen pro blower bmv200vs. Thanks for listening

I put this on a Murray Leaf Blower (same as Poulon pro) I purchased from Walmart and now it works better than ever. It starts easier and feels like it has more power. I was about to throw my blower away but this saves me money and keeps more trash out of the landfill.

It looks identical ! One thing I never had was the very special screw driverto adjust the idle and high speed fuel jets. I used one of the fuel bulbs.Runs perfect now!!!!

Installed like a dream in less then a hour. Only issue as has been mentioned on some other reviews was the one gas line for my Poulan pro didn't fit but some simple reaming of the plastic hole worked and i replaced both. Put a little gas in it and it fire up the first time. Didn't even need any adjustments ..