SealPro 134515300, WH45X10075 Washer door Bellow Seal Compatible for Frigidaire Made by OEM Manufacturer 134365200, 137566001, 137566000, 5304450475, AP3869103, PS1148773-1 YEAR WARRANTY

This fit quite well but was difficult to install. The quality was good and saved me from having to buy a new washing machine

This is no easy task to install for a first timer but I did it! This was half the cost of all the other places I price checked. My model is the Frigidaire Electrolux GLTF2940FS1.Tips: ~you’re going to want to lube up around the ring for successful installation (it’s the part of the ring with the holes...which face the inside of the machine not the outside). Some videos recommend silicone spray or dish soap, I used a small amount of liquid laundry detergent around the ring and the part of the washer it was going into and that worked. Otherwise it will just keep popping off (and it will drive you crazy).~There is a small notch at the 12:00 position in the tube that lines up with a small piece on the washer-start your installation there and the notches fit together to help hold the ring in place while you push it in in preparation for the first spring.~The white tubes are for holding the first spring in place while you stretch it around the bellow (you can find videos for placement)Lots of videos show disconnecting the power and taking the machine apart (disclaimer: follow advice to disconnect power for certain safety) I personally did not disconnect power, take machine apart or even take the door off when I did this.Hopefully this can save someone a little time! I’d recommend this product if you need it.

What can I say ? It's easy to dissemble in my case I have a Kenmore front load washer 417.48102701. Be warned the reassemblely is difficult when it comes to placing both the inner spring and lip of the bellow. Some key things to keep in mind use silicone lubricant spray for the inner part of the bellow and you will ABSOLUTELY need two 2 inch spring clamps. Overall the bellow arrived quickly and met exact specification for the install. I will update this review if anything should occur.

I'm writing this for those who may be uncertain about ordering this part. For me it worked great. It is not the identical original part for my washer but it is a very good replacement at a great price. Overall I'm very satisfied with the results. See pictures for before and after shots. A few points... 1) I had no prior experience replacing this part. 2) I was able to replace it without disassembly of front panel, just through the open door and without removing it. 3) YouTube tutorial says experienced technician takes 5 min to do the job, it took me 35 - 45 min net ( Not including break to go buy clamps ) 4) The included parts to help temporarily hold the inner spring in place didn't work for me. 5) I ended up using two 2inch clamps to help with the spring. 6) I held the spring at 12 o'clock first, then at 6 o'clock second, then worked around all the rest through. 7) I used soapy water to lube inner ring thinking using grease may later get into the wash/clothes. 8) Soapy water dried on me because of my longer inexperienced install time but it worked out. 9) The item ships folded in a box so it appears out of shape after unpacking. 10) To alleviate shape I left it for a couple of hours in hot (tap) water in the laundry sink, not sure this was needed but it worked for me.

It fit great but no direction to take old off or put the new on

Not the easiest to install, the pegs supplied only fit in a couple places around the tub and kept popping out. I enlisted my wife and we got over the hump. No leaks. I used some silicone grease and that helped. Carefully check around the lips to make sure you seal correctly.This part has drain holes at the bottom where the previous one didn’t. A nice addition!

Different than the OEM one. The product is folded and shipped bare in a box. Installation was a pain on my Kenmore but managed to it on after 2 hours. The outer rubber seal and edge is uneven. Tried a few adjustments and put on the snap ring. You can see the quality of the matetial in this aftetmarket and rubber is thinner and sages; and it does not form a tight seal. Tested a few cycles and water leaks from the bottom. Very disappoitment after spending hours installing and ajusting it. Going back to a replacement or refund. Reasonally priced but poor quality comparing to the original one.

The install tutorials are deceiving and don't accurately portray the tough stuff. I consider myself to be handy and technically inclined but getting this part on is tremendously difficult. It took me several hours of frustration and moments of defeat. However, it is definitely doable once it "clicks".And once installed, it worked flawlessly. It's definitely better than buying a new washer and it'll probably be easier the next time but I'll still dread the day I have to do it again.* Installation Tips: - Apply inner spring only after you have the rubber seal on and seated - If possible, remove front panel, this will provide more room for your hands - Stretching inner seal some is helpful but be careful not to overdo it - Outer spring is much easier to apply, pliers are an absolute must - Clamps were not necessary nor particularly useful - Included "tools" were useless