Syneticusa MB Retractable Tonneau Cover fit 2016-2026 Tacoma 5ft (60”) Bed

This roller cover is a great value. Seems to be well made. The install was a little tough getting it all lined up in the truck bed but not that bad. As another reviewer pointed out, the 4 screws that attach to the cover near the cab are silver and do not look very good since everything else is black. So I ordered some nice black aluminum license plate screw covers. I replaced the silver flat washers with the brass threaded washers that came with the covers. This way you can screw the black cover onto the washer for a secure fit. I used some thread sealer on both the security screws provided by the manufacturer and the caps. I think this made a great improvement in appearance and was really easy to do. I've attached before and after pictures so you can be the judge.

For the price you can not beat this cover. Instructions suck. Seller sent the wrong Cannister assembly in the first order and took them over a week to fix. They answer E-mails but do not seem to know much about the product. For 2019 Tacoma you will have to remove the TWO Tie down hooks in the front of the bed on the sides. Lay pieces out on floor, Support the Side rails with the foam from the package, Slide the Rolling portion of the top into the groove and Bring the rail just past the front of the cannister and screw togehter. Do the other side the same way. Lay complete assembly in the truck making sure that your front gasket is not bent under the cannister. Install Side rail hardware DO NOT TIGHTEN. Use the extra Piece of metal to hold the side rails apart at the back of the cover. And Adjust and center cover on bed check that the gaps are covered and tailgate close. Once you are satisfied with the alignment. Have Someone STAND ON THE RAIL and Finish Tightening down the Hardware to get a good seal. The Drain lines are WAY TO BIG. Go Buy some 1/2 To 3/8" Barb hose reducers and some 3/8 line. Cut two inches of the 1/2 Hose install barb and insert in the bottom of the cannister and tighten. Then install 12" of the 3/8" hose to the barb and run to holes in the bottom of your truck. You will have to make the holes bigger. BE CAREFULL THE Drain HOLE on the drivers side is RIGHT ABOVE THE GAS TANK FILLER TUBE> IF YOU DRILL TO DEEP You will damage this hose. Insert 3/8 Hose into the holes you made and your down. Pros: Lightweight, Easy to install, Looks good. Cons: Locks are Keyed differently on cover locks. (COME ON You cant get TWO Locks KEYED THE SAME?). Screws on top panel over canister are Silver not Black. Hardware for the side rails is not big enough to catch the complete rail. See pictures. Gets scratched very easy. The cover Got scratched from pulling a cardboard box off it. JUST THE BOX! NO Staples etc. Nothing in the box. The cardboard scratched it. So I do not Know how long this will last. I am Happy for know. Will update later. Does not seem to leak much more than any other cover I have had.

Good product. Installation is difficult. Videos online were helpful. Drain tubes are useless as they are too big for the drain holes in the bed of the truck (‘26 Toyota Tacoma). Low profile and slick looking though.

This "cover" is very clean looking and easy to use. Installation wasn't that bad. I own a 2019 Tacoma TRD Off Road. For this model I needed to take the top plate off and removed the plastic seal to make it fit cleaner. Now that its on it looks perfect. Not truly sure how it does in the rain and all, but from what i have seen around this is totally worth the money. 1 YEAR LATER: I own a media company and haul stuff expensive gear around, nothing has been ruined but 100 percent not Waterproof. Not fun when you come out in the morning and the gear and tools you have in the bed are totally wet. The drains that you have to drill through the bed are totally useless. Kind of sad. I loved everything about this cover until about 4 months ago when it started leaking. Will be upgrading to a cap next. Over all I do still like this, just wish it lasted longer than that it did (1 year).

Me gustó mucho este producto fácil de montar funciona perfecto muy buena calidad

Easy to attach and it is very sturdy and clean looking. The lock feature is priceless - you may need two people to assemble and install

This cover was difficult to put on by myself but I got it on. I loved that it was flat and could lock. The roll cage for the top takes up a lot of bed space which I didn't like. Worked well for a short time (a few months), but then stopped retracting. It also did not put up with the truck going on dirt roads and so the bolts would work their way free. I took it off last fall and have not been able to get it to retract at all. Definitely would not buy again.

Poor instructions. A manufacturer error led to the extremely difficult installation of this particular unit. It was impossible to install the bed cover into the track on one side as the lock mechanism completely blocked the track in both the closed and opened positions. We made the decision to remove that lock. The cover then went into the track as shown without seeming issues. Unfortunately that was not the end of installation issues. The bed cover would not roll out completely or return to the casing completely. After several hours of tweaking the adjustable blocks that lock the cover rails in place, the cover finally rolled out completely but roughly. It was at this point we discovered the second lock would not function as described meaning the entire cover could not be secured in an opened or closed position. My nephew took both the locking mechanisms apart and discovered that the internal housing (inside the black plastic casing) was installed backwards. Once he fixed that, both locks fit appropriately and operated appropriately. The rough rolling cover now rolled smoothly and fully into the opened or closed positions. The lock was an obvious issue with one side but the other side did not appear to be causing any issues. I do not recommend this installation to a beginner. If it weren’t for my nephew, this would have been sent back to the seller as un-installable. Also, The plastic drain hoses and the hose adapters do not match each other by size and are unusable. Otherwise, the cover itself works as expected.