Magigoo MPA2019 3D Printer Adhesive Glue for Nylon Filaments, 50ml

Using in a Bambu P2S with PA6-CF. Works extremely well. Pricey but worth it if you are using the expensive filaments. Easy to put on. Comes off easily.

Stuff is a life saver and for what little it costs compared to a failed 6 hour print it is value for the money. To put it on you just apply in the area you want putting lines down vertically then horizontally, that's it easy stuff. It keeps the materials firm to the base even with a less perfect level so it is plenty sticky. To clean the stuff just run it under some water and take a towel to it.

This is my go to glue for printing PA6, PA12 and such. This always helps with bed adhesion as well as release. Since using this glue I have zero issues, I've previously destroyed a build plate with a different product, but this glue is amazing and makes printing with PA6, PA12 and other higher end material a breeze.

This ain't it chief. I tried this and it failed. The build plate was garolite too and I had the chamber temperature at 72C and bed at 105C and still the print warped and peeled off the surface. I tried Nano polymer too and that stuff failed as well.

This is for the Nylon glue. It is fantastic! I had previously tried every possible solution, the best out of them being a G10 sheet, however it still was not working 100% perfectly, still was having issues with large parts, or parts with sharp corners, or parts with greater infill. With this glue on a standard textured PEI sheet, the nylons stick extremely well! For any size of prints I have tried, and for those that I was not able to print with any other method. Even after cooling down the prints are attached firmly to the surface! I am very happy with this product!

Works perfectly with PA filament. Arrived ahead of schedule.

I bought this product because Polymaker PA6-CF (nylon/carbon fiber filament) recommends this. It is easy to apply. I didn’t notice a big difference in adhesion using the product. The filament I used contracts a lot as it cools and easily pulls off the bed with or without this glue. I was much more successful with prints by using a raft and a 10mm high skirt around the part. The skirt traps in the heat from the bed and limits the cooling and contraction. This product is fairly expensive for what it does. I would recommend trying a cheaper glue stick prior to purchasing this product.

adhesive works well suggested for use on darkmoon build plate, doesnt not completly com off after use. cost a little more from amazon byt delivered quick

Ive got a couple of reels of esun ePA-CF. Its quite nice filament but it warps like anything. Its an absolute sod, peeling up after a couple of layers (60deg heated chamber, 100deg bed, brims, Hilbert first layer, slowed right down - tried everything) This stuff is expensive but it just works. No more warping, no more huge brims (depending on geometry). Very impressed with it so far.

Ich hatte immer Probleme mit warping bei abs pc und nylon, 9/10 drucke haben sich von der Buildplate abgehoben. Jetzt haben ich 50 Drucke am Stück mit allen Materialien komplett ohne einen Anschein von warping oder schlechter Haftung gedruckt. Absolute magie das Zeug!

Con esto te aseguras de que no se te despegue nada, incluso aunque haya un huracán. Estoy muy contento con el resultado. He impreso materiales técnicos, como nylon con fibra de vidrio, y ha funcionado perfectamente.

I tested the Magigoo Pro PA against my existing 3DPrima PrimaFIX glue for Sirayatech PPA and PPA-CF Core filaments and Sunlu PA6-GF25 on a Bambu Lab P2s Engineering plate heated to 100C and a build chamber temperature of 55 at the start of printing, rising to 63-65C. I did not test any other build plate temperatures. Comparing the consistency, the Magigoo Pro PA has a lower viscosity and is clearer when applied, leaving no bubbles, while the PrimaFIX is milky to begin with and leaves a few bubbles but these disappear and the film turns completely transparent once heated up on the bed. Both wash off completely with washing up liquid and hot water. The PrimaFIX provided significantly greater adhesion for all filaments even after 4-5 prints without reapplication. This could be a good thing or a bad thing. If your parts are prone to warping and require very strong adhesion, go with PrimaFIX. If you want to be able to easily remove the parts, and potentially minimise wear on your build plate surface, go with Magigoo Pro PA. I myself will continue using PrimaFIX, which is less than half the price.

fait parfaitement le job pour du PA, j'achèterais la version ABS par la suite pour comparer.