PSI Woodworking LA11418 Lathe Headstock Spindle Adapter 1-1/4" x 8tpi to 1" x 8tpi

The above picture of this adapter doesn't do it justice. I was surprised at the quality. This item is a large, heavy weight, finely machined and polished spindle adapter. Both ends screws on smooth. It's top quality at a price that's cheaper than PSI (Penn State Industries), sales it for. And a lot cheaper than other adapters are sold for. View my photos for more detail. It turns true and on center. It doesn't have set screws to lock it to the spindle for reverse operation, but I can drill and tap a couple of holes for set screws if it becomes necessary. It has a solid core on the male threads so you can't use a vacuum chuck. On the female end there are two flat spots for a wrench if necessary. I use an 'Adjustable Slip & Lock - Plumbers Nut Wrench,' its cheap light weight and can accommodate the large size of the adapter (search Amazon # TW408302). The adapter does jamb tight against the chuck and/or spindle so the wrench might come in handy. The nut wrench is also sold at local home improvement centers. This adapter screwed nicely onto my lathe's spindle, right over the shoulder of the spindle to mate with the shoulder of the adapter, as if it was made specifically for my lathe. I did read a magazine Q & A article where someone said their adapter didn't screw on far enough to seat onto the shoulder of the spindle and was asking if he could use a stack of large washers to fill in the gap. The answer was - not a good idea to use washers from the hardware store due to variation in hole ID and thickness from one washer to another. It was suggested to use 'Anti-Lock Lathe Spindle Washers' to fill in any gaps (search Amazon, about $2). Maybe this might help others, but it was not an issue with my lathe. Specs: OD at female end: 2 1/16" Depth of female pocket: 1 1/2" Depth of shoulder inside female pocket: 1/4" Length of male threaded end: 1" Total length: 2 3/4" Wrench size to fit flats: 1 13/16" Weight: 1 lb. 4.8 oz. [See my photos for more detail.]

Fits my lathe well. And fits in my chuck. Would recommend. Gets the job done!

I bought this to use with my new lathe and my old lathes chuck. My chuck is made for a 1" by 8 tpi thread headstock and my new lathe has a 1 1/8" by 8tpi tread headstock. This allowed my to use my old chuck for now without spending more money on a new chuck. It is simple to use. It is heavy and quite rugged. The threading is well machined and smooth. It has good stability in use. It is a reasonable price for the value. I would buy it again. The only thing you can,t do is use a morse taper putting it through the chuck as it is solid (not an issue for me). It also reduces your maximum stock length on your lathe by a couple inches.

well made

Perfect fit, works great!

I bought this adapter when I upgraded from an (very) old Delta lathe with 1 x 8 treads to a newer Jet 1824 electronic variable speed lathe with a 1 1/4 x 8 spindle. I had a large collection of faceplates, including some that were made into vacuum chucks that fit on the Delta spindle but not the Jet. It probably would have cost more than $150 to replace all these faceplates. Instead, I purchased this adapter. It also let me use the new lathe to finish a couple of projects that were in progress. The adapter was much more substantial than I expected for the price. In general, it seems very well made. I had two issues with it, both of which could be addressed with minor modifications. First, when I initially mounted a faceplate to the adapter and then to the late, I had a lot of wobble in the faceplate. At first I thought that the adapter was non-concentric. But the problem was that the thread on the PSI adapter bottomed out on the female threads of the faceplate and prevented the shoulder of the adapter mating with the shoulder of the lathe spindle. The wobble was reduced very significantly by making a 3/16 inch plywood spacer and mounting it between the adapter and the faceplate. It still has a minor wobble, but I am not sure if that is the result of the lathe spindle, the adapter or the faceplate. If the PSI adapter had been manufactured with a slightly shorter threaded portion use of a spacer would not have been necessary. Secondly, this adapter is solid, and therefore cannot be used as is with a vacuum chuck. I solved this problem by drilling a 3/8 inch hole down its length. The adapter is not hardened so its easy if you take your time. I was able to get a different spindle adapter for my Teknatool G3 chuck, so I will not be using this PSI adapter for use on the 4 jawed chuck. I think that changing out the chuck adapter is probably much better that use of this PSI adapter with a chuck, both because of concentricity and because the headstock to bowl distance is as short as possible. Overall I am satisfied with this purchase.

Perfect fit for my old Central Machinery lathe

Works well and I use it often.

its perfect for my BusyBee lathe!

Fast delivery. The part is exactly what I ordered. Thank you Amazon

Se adapta perfectamente

good device

Needed a good chuck for my shopsmith. This allows me to use the standard 1 inch threaded chucks. Perfect