Upgraded 2 Full set Toilet Seat Hinge Fixings Top Fix Nuts Screws Quick Release Hinges Fittings Rubber Back To Wall For Toilet Seat Hinges Replacement

Those guys need 6 stars... Use case: Duravit Stark 3 toilet with soft close lid. After so many years the attachment got all rusted and started to disintegrate. I lost 1 hour trying to find the official part, when I did it was unavailable. Then I found this product. There is no user manual...because... you don't need one. It's super easy, I did it in less than 5 minutes. Tip for unmounting before you replace. with the toilet lid vertical, use a large screwdriver to lift the plastic seat from the metal thing. Then you are left with 2 empty holes in the porcelain. As shown in the picture, the plastic cylinder black part goes inside the hole. Another tip: dont try to push it in the hole without the screw. So, 1/3 of the plastic black cylinder in the hole, add the screw on top and push. Hop it's in. Start screwing so the black part increases in diameter and locks into place. don't tighten too much until you ensure the position of the metal thing match the width of the holes in the plastic of the toilet seat. Then secure, add the metal cover and done. 2 negatives: the metal covers are not secured in place very well, but it's fine. second. The metal parts that go into the toilet seat actually dont "lock the seat". You can literally just lift off the seat, but I dont really see a practical problem with that. So thank you for the easy install and saving me money !

I recently pulled the trigger and purchased a bidet toilet seat. I own an American Standard Studio toilet that uses this style anchor for the seat. When attempting to install the bidet seat one of the rubber molleys that came with the original anchors fell down below into the cavity of the water closet. Getting access into the interior of these toilets is difficult at best. So I found these and ordered them. I only used the rubber molleys to replace my original ones but they worked with some care to allow my new bidet seat to be installed. Very nice to find them here on Amazon! I thought I would have to return the very expensive bidet seat. It now installed thanks to the ability to replace the original rubber molley inserts. Couldn't be more pleased!

I bought this product to replace the original set that came with my Swiss Madison toilet. These are much smaller, but work just the same. I'm hoping the coating on the cap doesn't rust like the original equipment did.

The posts are too wide to fit my Icera toilet seat. Need a thinner post.

It’s hard for me to know how I should rate this product, as it looks to be of good quality, and the rubber insert for screwing in the hinge is actually better than the plastic expanding bolt that it was replacing. But the post on the hinge was too thick for my Icera toilet seat. So it’s not a one-size-fits-all solution. (You can instead order the parts directly from Icera.)

Easy to install to replay toilet seat so worth it

The bolts that came with these were slightly shorter than my originals. Probably not a problem for most; however, I have installed a luxe bidet and these bolts were just a bit too short to work with that so I had to reuse my rusty original bolts.

Worked great ordered a second set. No more sliding toilet seat

Le ho acquistate ,le ho montate ma dopo poco tempo la gomma che le blocca ha ceduto e quindi il copri water si muove. Non le consiglio

The item works as it should. The only issue I personally had was that it was not the same size as the originals that came with the toilet. What I did to bypass this issue was I used the pair that it comes with and removed my original one so that the lid of my toilet seat could fit without issues. Had I left the old one on, they wouldn’t line up properly with the toilet seat. The original ones that came with the toilet were a bit bigger and they looked nicer IMO but nothing noticeable. Heck..it’s just a toilet seat hardly anyone even looks at! All in all…Good product! Would buy again if any other of my toilets need them. PS..if you’ve made it this far, when you’re installing the item, screw gently until snug. If you keep tightening the screw slowly, eventually you will feel it tighten up nice and snug. It may seem loose at first but keep screwing slowly and it’ll snug right up for you. Good luck!

Easy to install and worked perfectly.

They might not fit with the screws that come with it but my rubs work with the screws that came with the toilet seat I bought separately

Easy to replace , not needing to remove toilet