Shower Head Holder All Metal Handheld Shower Wand Bracket Adhesive Shower Wall Mount Holder Brass Shower Spray Holder Brushed Nickel, Drill Free Glue Installation

Being a short person I could not reach shower wand in its original installed position. I needed polished brass and couldn't justify cost of adjusted rail installation. These are an amazing quality and value. They are very sturdy and when installed, appear as though they are an original installation. I noticed the glue was from Germany, so I felt more positive about its ability to stick forever. Easy to install. I like the fitted sticky tape which holds it in place for the recommended amount of time for glue to dry. Glue also gives time to adjust and level. Recommended wait time is 48-72 hours. I gave it the full 72. Excess glue was easy to scrape off tile. FYI. I purchased two. One at a height for washing hair, and at about a foot lower I placed the other at a height for showering without getting hair wet. I am so thrilled with them. Super quality brass and construction. Easy to adjust after installation by moving wand. No more crashing down suction holders and wand in the middle of the night

Exactly what I needed to replace the one in my RV. Sturdy and works perfectly. Great value and works will with any handheld shower head.

Product looks great and installed perfectly to our tile with the included manufacturer glue. My package also came with temporary adhesive paper to hold product in place, while glue dried. This worked perfectly and peeled off clean and easy after 48 hours. The included adhesive paper indicates that the company is listening to customer reviews to implement improvements, as I saw past reviews mentioning challenges in the product holding in place just after glue is applied (Problem solved by company.) The company also proactively followed up with me to be sure I received the product and was satisfied. That impressed me and prompted me to acknowledge in a review.

Overall the quality of this holder is good, seems solid. My problem was with the glue that is supposed to hold this onto my RV shower wall - I glued it and was going to leave it for a couple days, but the glue would never set up enough to keep it on the wall. The seller should provide a faster-setting glue, or possibly a construction adhesive. So, my solution was to drill holes in the base plate and screw it to the wall (as the old one was). My shower wall has wood backing behind it, so I feel the installation is solid. The swivel mechanism in this holder is very stiff, so I have no confidence glue would have ever held it for long. I would also suggest the seller pre-drill holes for those who would rather do it this way. Now that it’s installed, I’m very happy with it. Shower head fits well onto it and the satin nickle finish is very nice.

I read a lot of reviews on this product. I saw that the main issue was adhering to the wall. I bought it because it looked like good quality. I rent my apartment, so I didn’t want to use the cement that came with the holder. I have had a couple soap dishes in my shower for years, held on with special 3M command strips (came with them). So I looked up waterproof 3M command bath strips (or something to that effect) and purchased a package. The first ones I tried didn’t stick to my tile, but I had showered recently and only towel dried the wall. (Not a glossy tile). When I had more time, I took a hair dryer and heated the area well, where I wanted to stick the holder, hoping for better adhesion. I also heated the command strips briefly. I stuck it on the wall and held it there until I thought it had probably cooled, then went to bed and hoped for the best. It was still on the wall in the morning, but I left it alone through a few showers before I tried it out. It has been holding for probably a month now. The holder itself is awesome! The ball is a tight fit, which makes it stiff to adjust, but it also holds position very well.

It has been several months and the holder is still on the wall holding my hand shower. Directions were good and unit was easy to install.

I had the plastic mount that came with my oxygenics showerhead. I wanted to get a shorter hose, and they are easily available, nice stainless ones, but they don't fit the oxygenics holder, which is too large. All other holders, like this one, are a 'standard' size. Most holders I found have the cradle attached to the shaft at 90-degrees, which severely limits the range of motion and allows moving the showerhead in nonsensical directions. This one is angled, which means the showerhead can be adjusted to point straight or downwards. It has a nice brushed stainless finish. The ball-mount holds firm and moves smoothly. Very nicely made. It can't be tightnened, but seems like it is well made and will stay put and not sag. It is provided with a mastic adhesive, which must be cured for 48 hours. Since the plastic showerwall was not attached to the wall, I found that the adhesive is not enough, so I drilled 2 holes in the corners, and screwed into the wall. Solid. I also applied silicone around the top edge, so no water could get in to loosen the glue. Very happy.

An excellent choice for additional hanging of your shower head high quality Make sure that you allow at least 2 days to allow the glue to securely attach to your shower walls also use some painters masking tape or other tape to hold in place while the glue cures and ensure that the holder does not slip while the glue cures

High quality product

El pegamento que trae no funciona, solo se mantuvo pegado 3 días y se cayó. El producto como tal se ve de buena calidad pero el pegamento no.

Tien très bien et belle apparence

excellent adhesion to ceramic shower stall,easy to reposition shower head while in wand bracket. metal bracket,not plastic.excellent quality.

Exactly what o ordered