Raijintek Compatible Morpheus II Core Black Heatpipe VGA Kühler

Awesome cooler, and fairly straightforward to install, unless you decide to keep the stock back and mid-plate like I did, then it may take a little bit of figuring out. I repasted the GPU die with Thermal Grizzly Kryonaut, as well I did had to use the supplied heatsinks for the chokes, which the stock cooler had a plate build in for those, and I used the K5 thermal pad replacement paste on those, instead of the supplied thermal pads, which in the reviews I watch never seemed to hold up well. The K5 paste is awesome! Holding strong, and keeping everything cool. Would highly recommend looking into K5 paste if you are going to do this, instead of the supplied thermal pads. As far as temps. It's cold outside, but I've been keeping my room warm around 23C, and my GPU has been idling around 32C and maxing out at 54C under prolonged loads. I'm able to get my GPU boost clock higher, and sustain the clocks speed now, with out thermal limits getting in the way. Only con: Which can be perceived as a con only if you have limited space, as with most ML120's it is going to make this a 4 slot card. You could use something like the NFA12x15 low profans to cut down on the height a little. Overall, easy to install. Near or at liquid cooling capacity without the worry of water ever leaking in the system, as well as much more affordable and cost effective I feel when compared to liquid cooling. Highly recommend.

So far, it's done pretty well. I slapped some Noctua fans onto it with the provided clips and it's quiet and cools fairly well. It was a little difficult seating the heatsink. You need 4 arms to do it properly. I ended up getting some adhesive rubber to hold the backplate in place (and provided some room to prevent component damage). Overall, it's not too bad. I will note that the 1080 didn't fit well with the large heatsinks so take that what you will.

installed this on a GTX Titan X(pascal) and stressed with furmark for 6 hours held 69 degrees (nice). although all but one of the adhered heatsinks did not stick. after purchasing my own and more heatsinks this thing performs better than on water

Besides the fact that the fan clips are an irritation at best and the cooler integration to the PCB is anything but easy, once properly installed, this cut my operating temps on ALL fronts almost in HALF! My hot spot temps NEVER GET ABOVE 120*F even during stress testing, normal gaming temps never above 112*F on my 1080Ti. My gigabyte water force extreme's water pump started screaming within 2 years of regular use, after installation of this kit, I've NEVER seen cooler temps..... This thing runs circles around oem AIO applications. 2x Noctua redux 1700RPM fans with a vga splitter cable truly unlocked this cards potential. I am well over 100% satisfied with this product, regardless of it's downfalls.

You need to have it packed better it's not packed right for shipping at all . I'll still keep it but I'm a little disappointed. I like the product I wish GPU mfgs would use this design. But please use a better box!! My GPU climbed right up to 85 °c not happy

Not easy to install and doesn't have a good blueprint to help and the fans it says that fit is a 120mm and those are way to big for the cooler

While building a new PC my 1080Ti that originally came with an AiO water cooler died due to pump failure. I wasn't ready to purchase a new video card at the time so I went with this doohickey. Works great! I was even able to get it to hold a higher overclock with this as opposed to the Corsair AiO that was OEM. The only con in my eyes is that you will never get all the heatsinks to stay where you want to the first try. I would suggest buying a thermal adhesive pad to freshen up some of the glue that comes on the pads that come with the kit, some had very little stickiness to them.

Some of the heatsinks have very small surface area, and some heatsinks had a hard time staying on. After a few heat cycles, they seemed to grip a bit better. But don't knock it around until then. Absolutely killer temps on a 1080ti - however after putting on some fans it's so big. Practically the only PCI device able to put on an ATX board.

Probably something I did. Despite looking at all of the youtube videos I couldn't get the fans attached and ended up using masking tape to stick the fans. Also, the tape used for the fins do not stick well to the chips. In any case, this is a sufficient solution with cards like the NVidia P40, if you know what you're doing.

1660sに着くことを願って購入しましたが、そのままでは付きませんでした。しかし穴位置的に加工すれば付けられそうだったので鉄プレートにドリルで穴あけ後ネジを切ったところ上手くハマりました。69℃→50℃まで落ちてくれたので加工してでもつけた甲斐はありました。試しに買ってつかなかった方、加工したらつくかもしれないので出来る方やっては良いかもですね。

Ich habe den Kühler mit zwei Noctua NF-P12 PWM verbaut. Leider liefert die Grafikkarte nicht genügend Saft um die Lüfter über deren Anschluss zu betreiben, wofür aber der Kühlkörper nichts kann. Also laufen sie nun mit Low Noise Adapter über einen Case Fan Anschluss des Motherboards. Verbaut habe ich den Kühler auf einer Asus GTX980 Strix, also kein Referenzdesign. Während die Karte vorher mit dem DirectCU II Kühler im Heaven Benchmark um die 70° warm wurde habe ich sie nun höher übertaktet (1500 statt 1400) und sie kommt gerade mal auf 55° (ohne Low Noise Adapter waren es 52°). Fazit: Mit einem guten Lüfter ist sie praktisch unhörbar. Die Kühlleistung ist überragend, knapp 20° unter einer Asus Strix, die eher zu den besser bewerteten Karten zählt. Absolute Empfehlung was die Leistung angeht! Der Umbau war kinderleicht und ging flott von der Hand. So, und jetzt in der Hoffnung dass Google die Rezension auch findet noch was zum Umbau einer ASUS Strix: (Was jetzt folgt bezieht sich stärker auf die Strix und deren Umbau als auf den Morpheus, ich schreibe es hier hin weil ich diese Infos im Vorfeld auch per Google nicht gefunden hab'.) Ja, sie passt auf die Strix. Eigentlich ist der DirectCU II – Kühler fast genauso aufgebaut wie der Morpheus mit Lüftern. Fetter Kühlkörper auf GPU, rest des Boards durch den Luftstrom der Lüfter gekühlt. Ich habe denn doch die Kühlkörper für die Speicherchips verbaut, beim Spannungswandler jedoch die werksseitig verbauten Kühlrippen drauf gelassen. Am wichtigsten jedoch: Ich konnte die Backplate drauf lassen! Da diese über einen Winkel mit der Slotblechhalterung verbunden ist gibt sie der Karte reichlich Stabilität, da hängt nichts durch, trotz des höheren Gewichts. Eigentlich ist die Asus Strix die ideale 980 für den Umbau. Die Backplate passt und stabilisiert die Karte, der Spannungswandlerkühler kann bleiben, die Speicherbausteine sind ab Werk nicht gekühlt, das heißt man kann die Kühlkörperchen des Morpheus einfach aufkleben. Das Kühlkonzept der Karte ändert sich eigentlich nicht. Einziger Wermutstropfen: Die Strix hat für die Lüftersteuerung einen eigenen 5-Pol-Stecker. Ein Adapterkabel musste ich in Hong Kong bestellen. Und dann waren die zwei Noctua doch zu stromhungrig für den Anschluss auf der Karte. Man kann auch da was basteln, um die Steuerung von der Karte mit der Stromzufuhr vom Gehäuse oder dem Motherboard zu kombinieren, aber da die Lüfter bei knapp 900 Umdrehungen praktisch unhörbar sind und die Karte auch unter Last locker gekühlt halten werde ich mir die Bastelei wahrscheinlich sparen.

I bought this for a graphics card I bought from ebay that didn't have the original cooler still. I couldn't find many 3rd party coolers that would fit the card and found no 2nd hand original coolers without buying a new card. The cooler itself is fairly big so make sure you've got space in your case. It's also quite heavy, but was sturdy and solid when installed. I followed a youtube video to fit this cooler but I didn't really need to. The instructions we good and the installation was hastle free. I bought a couple of quiet fans to use with the cooler which were fiddly but not too bad. Everything worked as expected and I now have a cool and quiet graphics card! Overall it's a good cooler and I would recommend it to others

Ottimo prodotto, molto performante. Se dovessi guardare l'estetica e la sua sua semplicità di installazione su una Vega 64, darei 2/5. Ma delle temperature così, ad aria...non le avevo mai viste. Consigliatissimo 😆