Comgrow PLA 3D Printer Filament, 3D Printer PLA Filament 1.75mm, Dimensional Accuracy +/- 0.02 mm, 1KG Spool PLA White

The media could not be loaded.  Before getting to the Comgrow filament review, I would like to point out that while filament quality do affect the quality of your prints, filament quality can only be assessed if the following has been done:1) Your printer has been properly assembled (i.e., all parts aligned, leveled, no hardware issues, etc.) and2) Your slicer settings are optimized for the filament you are usingI believe that if the 2 criteria listed above are achieved, most filaments will yield adequate print results, however, some will provide better quality than others. In this review, I will be comparing my observations of this Comgrow filament (tested white, black and blue) vs AmazonBasic’s regular PLA filaments (tried black, white, gray, blue, and red). Key differences are noted below.ComgrowAdvertised accuracy: 0.02 mmAdvertised temp: 180-210 CTexture: smooth filamentSpool: consistently wound, layeredPackaging: vacuum sealed w/ desiccantFinish: shinier/glossier than AmazonBasic’s filamentsOdor: nonePrinting: machine sounds smooth, effortless printing (subjective observation), more under extrusion observed vs over extrusion (fixable with splicer settings)Pros: price point is reasonable ($17.99 at the time of this review), prints really well, no residue on the retractor/filament feeder/extruderCons: few color selection (currently only black and white… I was able to order the blue when it first came out)AmazonBasic’sAdvertised accuracy: 0.05 mmAdvertised temp: 190-220 CTexture: textured/grainy filament to the touchSpool: not as nicely wound/layered like Comgrow’sPackaging: vacuum sealed w/ desiccantFinish: not shiny or glossy, more like a chalky finishOdor: nonePrinting: machine sounds like it’s working harder to print, more issues with over extrusion than under extrusion (which can be fixed with slicer settings)Pros: price point is very good for bulk orders (3-pack and 5-packs have averaged me at $10-13 a spool)Cons: so far, print quality is just okay. It’s not bad, but nothing I was in awe about (subjective). Noticeable residue on extruder (see images)CONCLUSION: when slicer settings are optimized, the Comgrow filaments provide very good prints (better that AmazonBasics in my opinion)Comments regarding photos:1. Everything in the pictures were printed with Comgrow’s filaments, except the Julius Caesar on the RIGHT2. The black dog was the first thing I printed after setting up my Ender 3 (no optimizing whatsoever)3. The residue on the extruder is from AmazonBasic's white filament4. I accidentally broke Monkey D. Luffy’s leg while removing the supports :(

The Comgrow PLA 3D Printer Filament has been an absolute game-changer in my 3D printing journey. This PLA filament, with a diameter accuracy of +/- 0.02 mm, has consistently delivered exceptional results. Whether I'm creating intricate prototypes or functional parts, the Comgrow PLA filament in black has exceeded my expectations.What sets this filament apart is its exceptional dimensional accuracy. It ensures that my prints are precise and reliable, eliminating the frustration of failed prints due to inconsistent filament thickness. The 1KG spool provides ample material for my various projects, making it a cost-effective choice.Printing with Comgrow PLA is a breeze. It flows smoothly through my 3D printer's nozzle, resulting in clean and detailed prints. The black color adds a professional touch to my creations, making them visually appealing.I've tried several PLA filaments before, but Comgrow's product stands out for its consistent quality and performance. Whether you're a beginner or an experienced 3D printing enthusiast, I highly recommend giving the Comgrow PLA 3D Printer Filament a try. It has certainly elevated my 3D printing experience, and I couldn't be happier with the results it consistently delivers.

REVIEW UPGRADE from 3 to 5 STARSMonday, August 14, 2023After adding a 2-Pin FAN PLUG PORT, (neeeded due to the long wire length for DRYER BOX to add any standard 40mm fan).ADDING A (40MM WINSINN 4010 12V Dual Ball Bearing Fan)NO MORE Fan Failure, so there was a fan quality issue, not a wiring electrical issue.AS the unit will be running for many hours non-stop replacing the FAN should be made a simple PLUG & PLAY replacement. Unscrewing and removing the base should not be required.______________________________________________________________________________________PREVIOUS OLD REVIEW:The DRYER has the potential to be great.BUT Sadly it's failure is the FAN, though the CUSTOMER SERVICE was 5-STARS!PROBLEM, is FAN FAILURE the FANS constant running in the heated enviroment for some reason destroys the FAN within roughly a week or two. It has to be an electrical wiring failure, because these fans can last over a year working within an enclosed 3D printer with an 110 celsius.So there must be a WIRING electrical issue burning the FAN out??? Or, the last 3 fans were lemons? Highly unlikely - I will upgrade my review to 5-STARS if I can put a FAN in that will last at least 3 solid month (90 days) of use.REVIEW UPGRADE from 3 to 5 STARSMonday, August 14, 2023After adding a 2-Pin FAN PLUG PORT, (neeeded due to the long wire length for DRYER BOX to add any standard 40mm fan).ADDING A (40MM WINSINN 4010 12V Dual Ball Bearing Fan)NO MORE Fan Failure, so there was a fan quality issue, not a wiring electrical issue.AS the unit will be running for many hours non-stop replacing the FAN should be made a simple PLUG & PLAY replacement. Unscrewing and removing the base should not be required.

This caused six failed prints in a row to properly adhere to ender 3 base. After reading some reviews here I was about to return them. However, I tried messing with the gcode I figured out extra supports seems to do the trick to get it to stick well. I doubled the amount of manual supports and it printed properly! Highly recommend messing with your supports if you have issues with it. I do not recommend making a support system that connects together, but rather individual points that snap off in small pieces, so it has more stick to the plate. If you make a grid type support that is connected in all one structure, should any corner lift, it will rip the entire project off!

Llego en perfecto estado, pero el producto llego abierto, la etiqueta de sellado había sido retirada, pero supongo que fue por el el proceso de aduanas ya que fue un producto de importación, de todas formas al revisar el producto que es lo importante parece ser que todo está en orden y que los filamentos aún conservan su empaque al vacío, más adelante actualizare sobre el desempeño de los filamentos ya que no he tenido tiempo de probarlo

Da un acabado liso satinado, no hay problemas de warping o de obstrucción del HotEnd, me gustó mucho más que los filamentos de acabado mármol

Un produit utile pour préparer ses bobines de filaments avant une impression 3D.Il est très pratique à utiliser avec deux boutons : un pour allumer l'appareil, l'autre pour les réglages de température et de temps.la température est réglable de 40 à 50 degrés. Le temps de chauffe est réglable de 6 à 12 heures.Un afficheur indique la température et le taux d'humidité à l'intérieur du boitier.

Hace su trabajo perfectamente.Revive tus acumulados filamentos y vuelves a imprimir como el primer día que los compraste.

No me gusto que el material viniera como si lo hubiesen desenredado y vuelto a enrollar, a simple vista parece que se atorara en cualquier momento pero estoy imprimiendo sin problemas. Me gusto que la bolsa en que venia estuviera cerrada al vacio y en una caja de carton.