PrimaCreatorFIX adhesive - Prevent warping

I used to suffer numerous bed adhesion issues, with prints become detached part way through, or lifting and warping. Even using brims to help adhesion they lifted. I tried Pritt stick, spray adhesive, hairspray, etc but nothing seemed to work. I even bought a new glass heated bed to see if that would help. After countless failed prints I thought I would try Primafix to see if that would give me any better results.I was a bit suspicious when the package was delivered because the box was slightly damaged, it looked like it had been opened previously and there was no instructions sheet in the box. However I applied it to the bed of my printer, it went on easily with the applicator and worked brilliantly from the very first print. Prints now stick every time even without reapplication, and I don't need to print brims because it adheres so well. As others have said, the applicator goes solid after a short time so I now paint it on with a small brush, but that is not a problem. On completion of printing the print is solidly stuck to the bed, and difficult to remove, however I have found that it I wait several hours until the bed is fully cooled (or even better overnight) it lifts straight off with a small tap. Excellent product - would definitely recommend.

Works really well on bambu cool plate, very easy to apply, if you are use to using glue stick and cleaning with water I found this comes off best with IPA but you get many prints before having to clean and reapply.

Purchased this after having terrible problems with bed adhesion on my new 3D printer.This was super simple to apply and solved the problem first time.It's super sticky when hot but not at all when cold.Prints stay stuck during printing but come away with little effort once the bed cools..Amazing!

Absolute garbage that cannot be removed and ruins print beds.It arrived with a totally different applicator than what it pictured but I managed to use it anyway. It's very liquid at first but does harden and stick well when it's heated.The problems start after the print where it will not come off the prints or build plate with any amount of water or scrubbing. I even tried alcohol which did nothing. Serious, I might have well have used super glue.Need to throw that build plate in the bin now, awful stuff.

I can only highly compliment about how good this product is. Apply a thin layer and as the base gets hot it gets sticky. When the printing finishes, with the base hot or cold, it is easy to remove the printed product. Much better than the prit stick approach and far less messy.The only minor complaint I have is when I received my new container of this magic glue it was in a small box that had looked like it had picked a fight with a much bigger gang of boxes. The containing box had been reused and when you open an amazon bag/pouch and that's the first thing you see your alarm bells ring. When I opened within it was obvious it was a new container of PrimaCreator, but first impressions, guys. The amount of sellotape holding the box together meant as soon as I tried to remove it, it tore the outside of the box away (the safety information). It looked poor.I will definitely buy again as it's a superb product, but I will know it might come in a reused box. I am all for recycling, just put that on your product page and it won't cause any issues.It's a great product and works brilliantly but I can't give a five across the board when it arrives looking like it's the glue equivalent of a hobo.

Sent this back, really it just made things messy rather than adhered the filament

I tried this as an alternative to glue sticks which can start to leave a film on your build plate whereas this doesn't and work as well as the best glue stick I've used.Very easy to use BUT will sponge tip can dry out and go hard if not used regularly but you can recover it with further use.

Great bed adhesion, easy application.However, cleaning up the base of the print afterwards it’s far too difficult. Warm soapy water does not get it all off. Tried scrubbing with a cloth and a brush but it still doesn’t remove all of it. Pritt stick or similar does a very similar job and the cleanup is much easier.Cleaning the print bed is a little easier. But not as easy as the same alternatives

Excelente adherencia para ABS, me encanta y es de los pocos que llegan a México de tan buena calidad. No cambiaré de marca, es lo mejor en adhesivo para impresora 3D

Absolut geiles Zeug.Ein dünner Film, bei 220x220 Heizbett ca. 3x pumpen, hält bereits so gut, dass ich bei PLA mein Heizbett mittlerweile nur noch für die erste Schicht auf 55° Aufheize und dann ausschalte oder je nach Größe auf 30° runter fahre.Kein Warping, perfekte Haftung (auf Glas) und nach dem Erkalten kann man seine Teile mit sehr wenig Kraft herunterbrechen oder mit einem Spachtel herunterschieben.Ich erneuere den Film alle paar Tage und löse dafür die alte Schicht mit ein paar Tropfen Isopropanol und Papiertüchern. Funktioniert wunderbar und Rückstände sind sehr leicht zu entfernen.Bei mir ist beim Herunternehmen gedruckter Bauteile noch nie Material in dem Kleber hängen geblieben. Meine Teile, auch filigrane Einsätze aus PLA, ließen sich stets sehr einfach und ohne Beschädigung von der Platte nehmen. Nach dem Erkalten auf unter ~25° verliert der Kleber den größten Teil seiner Wirkung - genial!Kaufempfehlung!

Es un buen producto pero es muy escaso y sale muy caro.

Fungerar okej men släppar oftast runt kanterna så ingen höjdarprodukt.

Hält sehr gut und ist leicht aufzutragen. Praktisch kein Abheben des Druckgutes von der Platte mehr (Warping). Ein Auftrag reicht für etliche Drucke. Hinterlässt manchmal auf dem ersten Layer einen weißen Rest, der sich aber abwaschen lässt (zB. Mit Sidolin oder waren Wasser mit Nagelbürste).Nutze ihn weiterhin sehr gern.