Siraya Tech Simple Water Washable 3D Printer Resin, Clear, 1kg

Although slightly on the expensive side, this resin is amazing, it looks n feels less viscous than other resins but I think that’s the beauty of it. Using other “specific” brands has caused me failures in the past, but this, perfect prints every time and it’s certainly less odourless

Good prints

A great low cost resin that's easy to pigment using liquid dye. Cleaning is also very quick and cheap. Mix 150ml of ethonol (IPA also works) with 850ml of distilled water. Only needs a short time in the liquid. Them blow dry with compressed air and then a hair dryer. Print MUST be quickly dried before curing in UV. The green colour in picture was made by adding colour from a 3d resin CMYK pigment kit.

This resin is NOT water washable AT ALL. Nowhere on the product descriptions or details for this resin does it say that you need to add alcohol to your washing station in order to clean this resin. I stumbled across the product specs on the Siraya Tech website when looking for printer settings and low and behold it says this: "5. Cleaning Notes: Simple V2 is best cleaned with 15% alcohol (1 part 90% alcohol + 5 part water). It could be cleaned with higher alcohol but is not needed to achieve great cleaning." I went through about half a bottle of this resin trying to clean the prints with water before I found that information as it isn't even printed on the bottle. No doubt I sent this back to amazon under false advertising for a refund. The only good thing about this resin is that it doesn't smell as bad as some of the others. If you are looking for a fully water washable resin then DO NOT BUY THIS RESIN. Go for the Elegoo 8k water washable resin instead for a fully water washable one or anything else. (first contact the manufacturers and find out if it is FULLY water washable)

Très bonne résine washable, facile d'accès aux débutants. Super résultat et super content, avec une saturn comme avec une Alkaid elle top.

Geruch: so gut wie keine Druckhaftung: bis jetzt immer Fehldrucke: keine Preis: Beste

Best value and save more money using water to wash. However need to cure for 30mins in a proper UV light curing station. My first model has crack all over. After some research, it was recommended to cure for 30mins which I only cure in a uv box for 3 mins. My 2nd attempt with 30mins curing time turn out really good, no more cracks.

[EDIT Aug 24, 2020 I have several prints from around the time of my initial review (July 8). For this test I printed 3 models with each resin mix: 100% Simple, Simple mixed with 30% Blu and mixed with 50% Blu. All were washed in 99% isopropyl alcohol, 20% iso and 35% vodka then rinsed with tap water and cured with a UV lamp. To date I've had zero issues with "melting" as others have reported. I used the same settings as I do for Blu (which come from the Anycubic Photon Google Sheet that is available in a number of enthusiasts groups). The 100% Simple is about as brittle as other standard resins, subjectively. The 50% mix was a little sticky after the wash/rinse for non-99% iso washes, and I didn't notice a significant difference in subjective toughness compared with the 30% mix. I did notice a marked increase in smell as I increased the quantity of Blu. ] I am a fan of the Siraya Blu and when I heard about Simple I had to find out if the low odor and clean up with 15% alcohol claims were true. I was too excited to try this and loaded up a model that has settings for Blu without really thinking about it, and Simple printed beautifully. I also found that the smell was hardly noticeable. I put the prints in my ultrasonic cleaner with an approx 20% IPA solution and cleaned them for three minutes. I was very pleased that there wasn't any obvious resin on the surface. Blu, on the other hand frequently felt gummy despite being cleaned with 99% IPA. While removing the supports they felt stiffer and more brittle than with Blu, but this resin isn't claiming to be tough. I'm going to try mixing this with Blu to see if it gains flexibility while retaining its low viscosity and easy clean up.

No acaba de curar bien, se queda pegajosa y es una lástima por que las impresiones salen bien!