Front Seat Jackers® - Made in USA, Seat Riser, Seat Spacer, DDI Original Design, Solid Aluminum, Factory Grade or Better Hardware, Compatible with Toyota Tacoma, 4Runner, FJ, and Lexus GX

7 years wasted driving uncomfortably. I had no idea these existed until recently when a mechanic buddy of mine informed me. I’m 6’3” and any drive over 1 hour in my Tacoma would leave my legs numb and in pain. However, after installing these seat jackers, I can tell I’ll be comfortable for longer trips. This brand is extremely well made. The jackers are solid, with perfectly sized screw holes and well machined. No headache installing, just undo the front 2 bolts, lean the seat back and install. Bonus: the seat jackers have machined screw holes on the front so if any of you guys are like me and like moelle panels in the bed, ceiling and under your seat, these seat jackers have machined screw holes to keep your mounts. Extremely impressed with the forethought (I was worried I’d have to drill these holes or find a new way to install). I see “value for money” listed as a negative on here. Ask yourself, would you trust some cheaper brand? This part connects your seat to the frame so do not cheap out. For the value, this is not bad at all. I can not recommend enough. Do yourself the favor and purchased these, especially if you’re tall.

Really changes seat position and comfort. I installed on my 2018 Tacoma and worked perfectly. Make sure to remove white factory inserts so peg will fit. Much easier to install when back seat bolts are out and seat is shifted back out of the way.

2019 Tacoma TRD Off Road Instant and significant improvement to seat comfort. This is a surprisingly good product, and truly changes for the better how the truck feels to sit in and drive. From the first moment you get in the seat, you'll notice that the seat feels much more comfortable, and the slight increase to the height of your sightline over the hood is beneficial and just feels much better overall. I am 6'0" with hip pain on my right side and wholeheartedly recommend this product. Installation is less than 10 minutes with nothing more than 14mm socket and wrench for the OEM bolts and a 15mm (or 9/16) for the supplied bolts. Pop the plastic covers off the rear bolts and loosen them slightly, then remove the front bolts, slide in and install the spacers with the supplied bolts, then reinstall OEM front bolts into the spacers and tighten everything down. Super simple and a major improvement overall.

Perfect for the 4Runner. Helps alleviate back pain which can occur with the 4Runner seats for whatever reason. They are extremely well made, heavy duty. Install is a breeze. I bought these for the drivers seat some do install for the passenger seat but I needed these for my back pain that occurs on long trips.

Hemmed & hawed over these (and similar knock-offs) for years. Balked and held off because of the ridiculous price for 2 pieces of milled aluminum. Still, if you want what they have, you either pay or go without, and, like they say: "Buy once, cry once." Yes, this is stupidly over-priced. It would be fine if it were for BOTH seats, but... it is what it is. And seeing as how 75% of my driving is solo anyhow, I just knuckled under and got the pair. There are NO INSTRUCTIONS (at least my set didn't come with them), so it might take some folks a bit to figure it out. Mine went in without a hitch - maybe 10 mins, tops, to install. It took some getting used to for the slightly different angle, but the additional room for my legs was a MAJOR comfort improvement. (And I'm not even that tall!) Fit & finish were first rate - no tweaking or fudging to get them in position. Included hardware worked as it should; (I added a drop of blue loc-tite to all bolts, to make sure they wouldn't work loose over time). (I suppose If my wife grumbles enough, I will spring for a set for her side, but she's much shorter than me, so I doubt she will.) Overall, quite satisfied.

This review is only for gen 2, Tacoma with Bench Seat in the regular cab, base model !!! UPDATE 2-22-25: After a little more than a week with these, I couldn’t take it anymore with all the ducking my head at stop lights, etc. I was able to pull the steering wheel all the way out to avoid it making contact with my legs but this also made it less comfortable in having the steering wheel closer. Feels too crowded. So I went back to the stock configuration. Conclusion is that if you have a 2nd gen Tacoma with the bench seat, I would avoid the Seat Jackers UPDDATE 2-12-24: I have determined that the raised seat compromises driving control / safety since the steering wheel is too close to my legs and due to the reduced visibility. Therefore, I have lowered my review to only a 3 star. If there was a height control on the bench seat, perhaps this would be different. Also due to the reduced visibility out of the top of the windshield, I experience neck pain as a result of ducking or cocked neck at stop lights in order to see when the light turns green. I am sure this would be a great product for Tacoma's with the independent bucket seats that do have the height control. ORIGINAL REVIEW 2-10-24: I have a 2012 Tacoma 2 door, Base model, 5 lug, with the single bench seat as opposed to the two independent bucket seats that most Tacos have. For the bench you only need two Jackers instead of four like the bench seats would need to lift them both. For the tight cab on the base model, wrench access was a little challenging but nothing serious. I found that after removing the two front seat bolts and loosening the two rear bolts, the bench seat needed to be rotated temporarily a bit during install to get the chair mounts out of the way. I have no torque wrench so I ‘wung it’ being sure not to over tighten which could strip the threads if not careful. I used a generous amount of blue thread locker on the original bolts and the bolts that came with the Jackers. Ok, job is done. First impressions are mixed as are final impressions. First thing I noticed was that my right leg barely squeezed past the seat and steering wheel as the seat is now an inch higher / closer. If my legs were any thicker, it would be a deal breaker. I’m 5’-10” and weigh 275 if that gives you any guide. Second impression was that my visibility was reduced. Drastically reduced? Well, visibility was already limited from the start, now I’ve lost even more upward viewing. Stop lights sometimes require ducking to see the light. The bench seat has no height adjustment like the buckets have. With the buckets people talk about not being able to get the seat up high enough without the Jackers and with them, they are able to use the height adjustment capability of the seat itself to bring the height back down. That’s one of the biggest downsides to the bench seat is no height adjustment. Part of the reason why the base model cost so much less I suppose. Now to discuss the whole reason for these things in the first place. Comfort. With the Jackers installed, it is much more comfortable. So much more comfortable that I’m willing to accept the tight pass below the steering wheel and the reduced visibility. The seat just now feels more supportive. I do still need to take a long drive before I am completely sold. I will update the review after that. So far, I suggest giving these things a whirl. Be sure to install them asap so you can have a little time to drive with them on and see if you want to keep them. For most women and many shorter men, there would be much less compromise. I don’t think these would be any help at all to tall people on Tacoma Base model with the bench seat but they may be appreciated by someone my size or shorter.

I’ve seen many social media influencers recommend this, I had to see what it was all about. I bought these for my 2022 Tacoma double cab. Tacoma’s are not known for a lot of space inside and I could tell my lower back would start to hurt after being on the road for a few hours. I’m 5’8” and on the hefty side of 260. These seat jackers are meant for taller people, but I found it works for anyone. It was uncomfortable at first having the seat tilted, but after a week or so, I didn’t even notice anymore. I don’t feel any pain in my back when I’m driving now. The install takes minutes. The seat jackers have a durable simple design. The only thing I’d say is that they are a little on the pricey side for being bolts and aluminum, but overall, I would recommend them.

Recently installed them in my Tacoma 2022 and it definitively makes a difference on your back, specially on long drives. It's easy to install and its built is sturdy and good quality.

Being 6'1 driving a 2015 tacoma the seat jackers really made my sitting better. If you feel like you need them just buy them, you wont regret it! They seem expensive but seeing the build quality and that its litteraly holding your seat to your truck you dont want to cheap out. I think its right to get these instead of ''knock-offs'' for $30.

Personally I like the way this product makes my sitting more comfortable

Don’t wait if you’ve ever considered these. Amazing and comfortable and just what your Tacoma needs. Very pleased with these and were in fact pretty straightforward to install.

Fits right

This tilts the seat back to a more natural position.