Curved Crystal Screen Protector

This works perfectly for the samsung galaxy s7 edge. This screen fits perfectly on the phone with almost no room for errors, so try to get it as centered as possible. The edges stay flush when put on. A few tips, center the speaker, front camera and sensors on the front and it should be centered. Align the home button and you are good. Try to not have any bubbles as you push the screen protector down because these are harder to remove then normal screen protectors. The screen protector will not automatically cling to the phone. you will need to push it down so this helps to avoid bubbles. Work from the middle and take your time to press it against the phone to avoid bubbles. Important to know that the front and back plastics that cover the screen protectors are pretty hard to take off. I found the tabs came off without the covers. So go slow and make sure the plastics come off because if the front one does not come off and you leave it on, the edges will not stick.TLDR; Be patient. Press slowly to avoid bubbles (these are hard to remove after). Make sure to remove front plastic off of the screen protector or else edges will not stick.

Fits great and works great with my Spigen case. I installed as directed and it went smoothly. I am amazed at how well it fits the screen... You can't even see the edge of the protector because it aligns so well with the edge on the screen.Only complaints I have is that is smears easily and is sunlight you can see the plastic imperfections.

Spigen Curved Crystal Galaxy S7 Edge Screen Protector with Crystal Film 3 Pack for Galaxy S7 Edge Well, I don’t really do reviews, but decided to do one here. I’d been looking for a good screen protector for the S7 Edge and had been reading all the reviews I could. I read all the “10 best protectors for the Galaxy S7 Edge” and all I got was a very generic description of the product. Not how they performed.I ended up reading all kinds of reviews and narrowed it down to 6 different protectors. I ended up buying all 6 to see which I liked better. I really wanted to buy a glass protector to try, but pretty much all of them had stories of them just cracking. My conclusion was that the curves on the glass ones either are not precise enough, the variance on the phones is too great for a hard protector to work or some other factor I am not getting. But in any event, I decided that the current technology really does allow a good glass protector for the curved edge S7 Edge. I felt that it had to be a pliable protector to stand a chance of molding and staying on, so all 6 of these are the flexible, non glass type. They also were some of the highest rated protectors.The 6 I bought were the following:1. ILLUMI AquaShield Full Coverage Screen Protector for Galaxy S7 Edge HD Clear Anti-Bubble Filmby AquaShield2. Armorsuit MilitaryShield - Samsung Galaxy S7 Edge Screen Protector3. Galaxy S7 Edge Screen Protector [ Not Glass],Yootech [Full Coverage][Case Friendly]4. Galaxy S7 Edge Screen Protector, Skinomi TechSkin (2-Pack,Case Friendly)5. Galaxy S7 Edge Screen Protector, IQ Shield LiQuidSkin Full Coverage Screen Protector for Galaxy S7 Edge HD6. Spigen Curved Crystal Galaxy S7 Edge Screen Protector with Crystal Film 3 Pack for Galaxy S7 EdgeThe most intriguing was the Spigen. It says curved crystal, but it is actually a plastic film that is curved. I thought it would be the best compromise. A flexible plastic but still molded curved. It turned out to be the worst by far of all six. It simply did not fit properly. It only would stick on one edge or the other. I had seen others say the same in reviews but I still liked the idea so much and there were enough good reviews that I still wanted to try it. It really is a waste of money. I am returning itThe next one I tried was the Skinomi. I had had good luck with their products in the past and thought this would be a good bet. The Protector was too small in my opinion. It was too short and it also was not wide enough. Its edges were in the middle of the curve and my fingers always felt them. I did not like it. The film felt good and adhered well, but it did not fit well. I am also returning that one.After seeing the lack of fit, I measured the width on the second screen protector. It was about 71mm. I measured the rest and found that the AquaShield and the Armorsuit were even smaller at 70mm. I know if I did not like the feel of 71mm, I was not going to like 70, so I am just saying that they do not fit properly and am returning them. They really need to be wider to cover properly.This leaves the last two – the IQShield and the Yootech.The Yootech had the highest ratings and it did not disappoint. It did not go all the way to the very edge, but it was very close. I could not feel where it ended with my fingers. Probably with fingernails, but that is not how you use the edge. You have your finger run across or touch it on the curved part and for all intents and purposes, it was full width. The cloth was made out of a material that cleaned the screen and the protector well. It gave you some dust stickers and an alcohol cleaning pad. The openings were cut well. The protector did not go all the way around the openings, but it went up to them and surrounded them. I do recommend this protector. The adhesive was aggressive and it sent on the easiest. The only nits I have to pick is that the material is not the hardness that some of the others were. I can’t say it feels gummy, but just not has hard as some of the others. It probably needs to be to stick so well. The other nit is that because of the softness, it is easier to trap bubbles under it. I have two very small ones. I can take it off and re-apply but they are too small to really worry about it. My theory is that since the material is softer, the plastic does not help to push out the bubbles as well. You really have to be meticulous and make sure all the bubbles are gone.The last was the IQ Shield. It measured 73mm and truly went edge to edge. The material is harder than the Yootech and I like the feeling better, but it shows fingerprints too easily. Kind of like a greasy residue even when you have just washed your fingers. The cloth they give you is not as good as Yootechs. When I cleaned the screen with it, it remained hazy. Then I used the Yootech cloth and it was clean. It takes more patience to install this one because it is harder and you have to keep coaxing the edges down until it finally dries. It goes right to the very edge and that is good, but I am also worried that there may not be enough play when I put on a case and it may lift. There is no alcohol pad or dust stickers, but the fit is the best and the openings go all the way around what they are protecting. The nits on this one are that the screen really gets hazy quick and will be a chore to constantly keep clean. It is also a recommended protector.I am going to buy a few cases and see how the IQ Shield and the Yootech can withstand them. That will tell me which one I really want, but I think these two are the cream of the crop today. Picking a protector for this phone is a chore and I took the time to do this hoping that it might help someone.

I see a lot of reviews saying that the edges don't stick but honestly I've had this screen protector on for the past few days and the edges haven't lifted not once. Not sure if it was because of the method I applied it plus the fact that I put it on almost near perfectly symmetrical.Just a few tips on my procedure:1. Made sure to put the guide sticker to adhere to the phone itself on the side that doesn't have the peeling tabs on it. So basically leave the side WITHOUT the peel tabs stuck on the phone then leave the other side with another guide sticker with the yellow peel on. This makes sure it is easier to peel off the bottom layer peel tab of the screen protector.2. Once the screen protector is on and aligned as best as you can put it I made sure to squeegy out the bubbles and right after that I immediately began continuously pressing down the edges until they stood down. Mind you this is me doing this step still with the top film still on. I think since the top film is more rigid that me pressing down the sides with it still on helped make the button final screen protector get easily shaped to the edges.3. When I started to peel the final tab I noticed it gets caught on the bottom final screen protector film and wouldn't easily come off so what I did was I peeled it a little then I used the squeegy to pry the films apart. Do it to the whole bottom part of that screen protector and then you should be good to just hold down with your fingers and pull off the top film.4. Last tip, after the final film was on I still had one or two bubbles. What I did was put the previous film back on the screen protector but not aligned in the same position but horizontally. Then squeegy out on that layer as apposed to the final screen protector itself. So maybe having the sticky film squeegy out bubbles on the edges also helped assure them down.Hope that helps. As I said before I've not seen any edge lift for me whatsoever. Don't forget I also pressed down the edges right away to keep from any dust to go in plus I never ever touched the bottom of the edges at all not even with nylon gloves and I think that made sure to keep it from lifting.

Parfait

Todo bien, gracias...

This IS hands down the best screen protector for the S7 Edge. Any people bashing this protector should come to terms with the fact that you are not meant to put screen protectors on phones. Possibly due to fat fingers, shaking hands, or simply overall clumsiness. When properly installed, this screen protector offers perfect edge to egde fit with no air bubbles, you can apply phone cases without lifting, and fit is absolutely perfect. I personally found this protector to last at least 2 years of average use before you want to look to swap for new due to light scratches and scuffs developing over time. Buy the 3 pack and it will out last the life of the phone. Well done Spigen, keep up the great work!

Sono un po difficili da adesivare, non più delle altre.Sono PERFETTAMENTE compatibili con tutte le cover della stessa marca Spigen.Senza nessuna esperienza in pellicole, io come prima volta ho eseguito una installazione perfetta al 99%, non ho soltanto visto 3 granelli di polvere sul display prima di mettere la pellicola ma posso garantirvi, come vedete dalle foto, che calza perfettamente ed a pennello, in più i bordi vanno a finire SOTTO la cover per almeno 2mm, non accanto o sopra, evitando in modo assoluto il problema che si stacchi o si scolli.Una volta messa non si vede assolutamente che ci sia una pellicola sopra, trasparente al 100%, touch funzionante in modo impeccabile.Per montarle serve solo un po di manualità, un po di "calma" ed una cover Spigen (non una generica). Ottimo acquisto IMHO.

I think I have tried every single screen protector sols on Amazon for my s7 edge and all of them have either been Meh! or down right rubbish.Despite not great reviews i thought I would give it a try as I have bought Spigen cases for past phones and found them to be a great brand. Its a fantastic screen protector and was pretty easy to attach (Watch the how to on youtube). Clean the screen and attach the guides to the protector then peel and place on to the screen. It took roughly 10 mins from start tofinish including pushing a few bubbles to the sides. Crystal clear screen and fits the edges perfectly and also can be used with bumper cases.