Guyker Guitar Locking Tuners (3L + 3R Handed) - 1:18 Lock String Tuning Key Pegs Machine Head with Hexagonal Handle Replacement for ST TL SG LP Style Electric, Folk or Acoustic Guitars - Black

These arrived very promptly. I had an issue with one of the tuners, the collar wouldn’t tighten down far enough against the headstock. After contacting Guyker they sent a new one free of charge; that’s now fitted and working fine. Great customer service!I would say they’re not quite as good as really high quality (and expensive) locking tuners, but they do a really good job, look great and hold tune well.If they were twice the price, I don’t think anyone could tell, they’re well made and finished. The only one very small issue I had was that on a very light string, I tightened it a bit too much and broke the surplus string off. This wasn’t an issue since the remainder of the string held tight in the tuner; not sure if more expensive tuners would do the same when over tightened. (I’ve since learned that you shouldn’t and don’t need to tighten these down hard.)If you can, and want to spend more for Graphtech or Fender locking tuners, you potentially should, but these make an excellent alternative that don’t disappoint.Good value for money, hence five stars.

Great upgrade for my ESP LTD TE 401. Highly recommended for this price. Fits my guitar perfectly!

Excellent value and a nice looking locking tuner... especially with the guyker script on the button. No problems at all installing although the securing screw is at a slightly different position from my old tuners so needed to make new holes. This might not apply to everyone. They are cheaper but (and this is my opinion only) just don't seem quite as good quality as Vanson tuners or Wilkinson ez.. (I personally also prefer the button style on those two alternatives.) However, a definite upgrade from the usual tuners found on the sort of guitars many of us can afford

Just took the plunge on these Guykers and I’m totally sold on the quality. I have Gotoh’s on two other of my guitars and these stand with them on quality, finish and fit.I’d read the reviews about bushes not being a good fit, tight stems, so I pre-tested all of mine before fitting, they are all spot on.Save some money peeps 🙌🏼

I was very happy with the build quality of these. The replaced the wobbly stock tunners. The locking mechanism was simple and clear to use.

Can highly recommend these budget locking tuners. Pretty good gear ratio for stability. Saves a lot of time when re-stringing, and most importantly, they lock. Tight. Really happy with these.

Ok, so if you're tuner hunting like I was you really only want to know the following things... So here we go!1. They look great. They're excellently machined with a rich gold finish and they look and feel premium (just as nice as the official Fender tuners on my Strat... At half the price).2. They work! So easy to change it strings, stable tuning and they don't drift.3. Fit requires a small, easy adjustment for My Bonanassa Custom ... So probably most LPs.They're a shade too narrow on the collars (but this allows a greater variety of instruments to use them... Better than too wide!).All you need to do is get some some tape (I used scotch tape). Cut around 6cm of tape and slice it down the middle, length waysThis makes a perfect width to tightly wrap around the collars, creating a shim (expanding the width).They will now seat in the headstock snuggly.With that done, line the tuners up parallel (just eyeball it).4. The screws! As you can see the fixings are 45° not right under the tuner. For me, this was just fine as my original screws were spinning from re-tightening over the last 20 years.5. You don't need a drill to fit! Before you take a drill to your axe... Read the following!Firstly, line them up. Next, you'll need a fine center punch tool and a hammer (the ones you tap into wood to start a drill hole).Line the centre punch up with the screw hole and GENTLY tap the punch into the headstock. ROTATE it as you gently remove it (don't wiggle it out ... You'll risk splitting the wood).Pop the screw in the starter hole and slowly and carefully screw it in. If it doesn't want to go in... Use the center punch again gently.Using this method I achieved a perfect fit for all screws in less than 2 minutes... Without using a drill.They now look amazing. I'll not fill in the original screw holes in case I ever want to reinstall my Grovers (unlikely as, unexpectedly, these are better).The guitar now feels stunning to play. String bends don't drift the G string and it's weirdly quicker to tune... And rock solid tuning stability once in.Many negative reviews for off-brand guitar parts are a result of a lack of ability to make simple adjustments. There is always size variance between models and brands of guitar...a bit of common sense, some basic tools and sticky tape can save you a fortune.My advice would be to buy these and follow these simple instructions ... Rather than spanking nearly £200 on Grovers.I hope this answered the questions I needed to know when I was browsing!Rock on!

I purchased these to go on a cheap fender Squier so didn't want to spend a lot, they are really good for the money, but two were stiff.. but replacements were sent out straight away..

I had purchase a very cheap set of simliar tuners and they had knobs that were breaking loose, and when I tuned the guitar, there was a lot of slop in the mechanisms. It was very difficult to get the guitar tuned. I sent that set back and replaced them with these tuners. It was night and day different. These tuners look sleek, seem to be solidly built, and there was no slack in the mechanisms. Tuning was a breeze! I am very impressed, especially at this price point!

These are the best-locking tuners for the price range.

Just perfect

Muy buenos y preciosos.

Genial et a sauvé la vie de ma vielle pelle... Super système de blocage ! Prévoir d'agrandir les trous pour certains modèles... A recommander !!!