Peerless Industries SmartMount Universal Tilt Wall Mount for 46-90-Inch Display

I wanted a bracket that can hold a super-large TV. This one does the job well. It's very sturdy and I have no doubt that it will last forever.

I purchased this wall mount for a new Pioneer PDP-6010FD 60" plasma flat screen, and can highly recommend this mount. It is engineered and built with superior construction quality, easily holding my plasma TV weighing about 150 pounds (rated up to 250lbs). Mounting the universal bracket to the back of the plasma was extremely easy, just four bolts and washers (provided) that locked down, make for an extremely rigid mounting of the TV onto the bracket.Since this mount covers televisions up to 71", it should work for most sets, as long as the maximum horizontal distance between the mounting holes is about 35" or less (check the product manual to get the exact maximum distance). The bracket's width and weight handling capacity requires that you mount it onto 3 wall studs, as it is approximately 40" wide. However, this actually helps you with mounting the bracket in a very level manner.Here is a short narrative of how you go about mounting your TV using this wall mount. First, locate the center stud that will be used as the center mounting point, and use one of the provided lag bolts to mount the bracket on the wall at the desired location, using the topmost center hole on the wall bracket. Now mount your level on top of the bracket and using the installed center bolt as a pivot, rotate one side of the bracket or the other until your level indicates that the mount is perfectly level. Now using a marker pen, mark the two points to be drilled on the left and right outer studs, perfectly centered in the desired mounting holes. Drill the appropriate holes, then screw in the lag bolts, fixing the bracket into a perfectly level position. Now mark, drill for, and mount the remaining 3 bolts (there are six total, two at each end and two in the center mounting positions.)The final step is to mount your TV onto the wall bracket and secure it. With help from a friend, securely grasp the TV and "hook" it onto the wall bracket. From underneath, reach behind with a standard or phillips head screw driver and secure the lock screw on the bottom of each bracket hook. This final step secures the TV to the wall mount.I'll tell you, I live in the heart of earthquake county in SoCal, and I fully believe that my house will suffer damage well before this TV comes off the wall in a seismic event.Overall, this wall mount is well worth every penny. Like always, Amazon comes through with a great product at a good price.

I purchased two of these mounts for a 50" and a 60" Pioneer monitor. The Peerless website was helpful to make sure I choose the correct wall mount model # for these particular monitors. I liked the feature to adjust the screen tilt anywhere between -5 degrees to +15 degrees.The wall mounts were sturdy and very well made. All parts were neatly packaged and well labeled. The installation instructions were straightforward and relatively easy to follow. It took about 1 hour to install each mount, with most of that time spent on picking a good wall location, deciding on a good mounting height and finding the wall studs using an electronic stud finder. For the best results, make sure that you take the time to fasten the mount to the center of the wall studs and that the mount is perfectly level.One issue came up that was not addressed in the installation manual. There are two parallel sliding tracks on each bracket that attaches to the TV/monitor. These sliding tracks are used to adjust the screen tilt. The instructions discuss a manual tension adjustment on one of these tracks using a built-in ratchet handle. The tension on the second track was too tight and needed to be adjusted but the instructions did not discuss this. I neded to use a 3mm hex head driver and a small wrench to make this adjustment.One other minor issue is a reference in the instructions to a screen compatibility chart on the Peerless website that is out of date (June, 2006 was the last update).Overall, I would recommend this product.

I ordered a Sanus 32-50" wall mount for my 50" Samsung plasma, but due to the 24" spacing between studs in my wall, and the large width between bracket holes on the back of my tv, I couldn't mount it without my TV being off center horizontally on my wall.I then looked for a wider mount, and found the Peerless ST670P. It was wide enough to still grab two studs, and accomodate the greater bracket width of my tv, and the end result is my plasma perfectly centered on my wall. Installation is very simple and straightforward - you really do need a stud finder and level. It comes with all the bolts you need, and where the Sanus came with M8 bolts that were too long that I would have had to cut to fit my tv, the Peerless model came with 3 different lengths of M8 bolts, so the bracket installation into my TV was perfect.Quality construction. I really recommend this product, and will be buying another when I get another plasma one day!

After an extensive search to find a mount that would work with my Panasonic TC-P65ST30 I decided to try this Peerless mount. I wanted a mount that attached to three studs and was rated for at least twice the weight of the television (TV weighs ~100 lbs and the mount is rated at 250 lbs). The backplate and arms that mount to the television are made of a good quality steel. The hardware is also of high quality, which is a big thing for me (I hate having to buy new hardware for kits). The mount was very easy to install (I would recommend a laser level as opposed to what the instructions say to use).The reason for 4/5 stars is that the arms that mount to the television were very stiff. They would not rotate to allow for viewing angle adjustment. I found that them apart, adjusting the angle, and then reassembling seemed to do the trick. This is not something you could adjust on the wall.I would recommend this product.