OVERTURE Rapid PETG 3D Printer Filament 1.75mm, 1kg Black

Excellent filament. Does need drying before use but that's not unusual for PETG. Give a beautiful finish and, even at 0.20mm height, layer lines are almost invisible. Used OVERTURE profiles for PrusaSlicer and got good bed and layer adhesion. This is my go to PETG filament and offers trouble free printing at a very reasonable price.

If you have ever tried to print 'glass' on an FDM printer, you will be familiar with the frustration and poor results that are usually obtained. Well, with a little tweaking of settings, making sure all lines and supports are printed in the same direction, high temperature and no cooling. This product with careful settings will print the closest thing to glass you will ever see from an FDM printer. Almost perfectly clear. Absolutely ideal for all those models out there that have clear parts or just as an interesting effect for ornaments and gifts. It does take a while to print, but the result is worth the wait. This product is the only one I've had consistent success with and that has printed perfectly every time. Be aware though, you need a HOT temperature to print with this, so it won't work in printers with a limited temperature height. Great price for a great product. Especially as it actually works.

This is my usual “go to” filament. It’s usually dry right out of the box, well wound and prints really well. I’ve bought Overture at least 10 times and have been impressed every time. However until my last order. I opened the usual Mylar bag, first off it appeared tangled, most unusual. It looked like it had been rewound by hand. Secondly when I loaded it into the printer it hissed and popped like never before, so wet. Then I tried to print it just clogged, so much I had to rebuild my hotend. So while I was rebuilding I tried to dry it out for 48hrs and it was pretty grim. Very poor finish. So I’m going to send this one back. See photos. 1st is the dodgy batch, second is the usual quality from the end of the last reel. So is this dodgy 1. Just a QA mistake 2. Counterfeit 3. Really old stock? Who knows?

I used Overture Rock White PETG for a larger 'functional' print, and it's worked out quite well. I have Bambu printers which print pretty fast - too fast for this filament. My first print I could pull apart quite easily with bare hands. Instead, I found at 0.2mm layer height with a 0.4mm nozzle, I had to keep the speed to 150mm/s or lower. At this speed the quality was excellent, and the print seems to be as strong as any other PETG print. The behaviour seems to be the same as normal PETG, and all that entails (flex, less brittle than PLA, etc.). Appearance-wise I think it's pretty stunning. It is a very vibrant white which is what I wanted. I've provided a photo comparing this Rock PETG to eSun PLA Marble. The surface is matte rather than shiny, which is unusual for PETG. The surface feels rough to the touch, rather than shiny and smooth. The 'black' pieces I think are very shiny because if they reach the surface they appear somewhat mirror-like. Occasionally this can result in a blemish on the print. I think a piece gets briefly stuck on the nozzle and drags for a bit. This can result in a line or 'divot' where it was dragged. I'm not sure if you need a hardened nozzle when printing this. I would follow the general rule that if there's anything else in the filament (glitter, fibres, etc.), use a hardened nozzle just in case.

I bought this filiment in rock white and I'd like this to work better but it's just so awful to print in. If you can get this to work then it looks great. I've had some luck on very larger items but not without there being problems when the filiment is pulled round tighter corners. I've tried slowing down print speeds as well as heating the bed and nozzel to higher tempritures but I recon i've thrown out half of what i've printed. My best advice is if you do buy this is then make sure it's bone dry but i really couldnt recomend buying it. There's a lot of stringing, especially going round tighter corners and the top layer quality is pretty poor what is probably in part because of how poorly it prints in the infill

Hi, works really well, you do need the right settings mine was 245 nozel temp , bed temp 75, prints worked first time, using it to make aquarium caves and feeding holes, and plant pots, better under tropical water heat than pla, very good stuff, good value and arrived quickly 😀

I bought a brown PETG filaments and the quality is poor. The temperature on the roll is 230-250. That is completely wrong. On 230 degrees it comes up from the plate. The item on the picture made on 250 degrees and still goes to the bin. Now half a roll is wasted and I’m testing on 268 degrees which is far above the specs. It is still meesy but a little bit better. I will not buy this filament again. The temperature for this product is 268C. Using that temperature and the 10mm/s speed working fine. Unfortunately, all specs on the product were wrong. Using my settings I can print this product fine.

i have been using forever and it still performs creat prints and at a great price, just love the material Printer Elegoo Carbon hotend 243 and bed 60c either on silent mode or normal not tried on higher speeds

Models keep warping when using this filament, but for the same model when using other filament is okay. Would not recommend it, waste of money and your printing time

Fatica a fare stampe particolari