Reboot E71T-GS Gasless Flux Cored Mild Steel MIG Welding Wire, 0.9mm (0.035") 1kg Spool – Self-Shielded No Gas Wire for DIY & Outdoor Repair

braght this quite a few times and is now my goto when I run out of wire lasts along time precedes very little splatter and excellent welds, as always very happy with this product and reccomend to anyone

Over the years i've used a fair few varieties of gasless wire on those jobs that would be a nightmare trying to keep the gas where you need it, and generally speaking the only stuff that works as it should comes with a hefty price tag. This little gem, however, has genuinely surprised me! If you're new to gasless wire, Its important that you know that gasless is NEVER going to behave quite like using regular wire with gas. There WILL be more spatter with this stuff and there IS a coating of slag that is probably not going to completely clean off without some work. But if you cant use gas, or you need to weld outside, or you simply want to weld without the complications and expense of a good gas setup, this stuff is fantastic. I imagine there are going to be alot of people buying this who are just starting out welding or haven't done much, so a few tips: Make sure your machine is set to the right polarity for gasless wire (torch negative, earth clamp positive), if your machine is gasless-only (doesn't have the option to even connect gas) then you wont have to worry about this as your machine will be permanently set to torch negative. Also some machines will have the option for gas but NOT the option to swap polarity for using gasless wire, so bare that in mind (sometimes you can swap them inside the machine mechanically, but this MUST be done by someone competent in high current high voltage systems. Make sure your EARTH clamp is connected to CLEAN and preferably shiny material! Most small machines come with hopelessly underwhelming earth clamps, they can still be used if you take care to always connect it to a clean piece of material. You can also massively improve the reliability and performance of these cheap earth clamps by brazing some copper or bronze onto the jaws (copper and its alloys are far more conductive than steel, so you get a much better connection per surface area) Finally, play with wire speed. Take a piece of scrap and start welding with one hand while adjusting your wire speed with the other until you get no stuttering, no excess spatter and a smooth rhythmic arc noise, you'll know when it sounds "right"! Well that's my 2 pence, hope somebody finds it useful. Highly recommended wire, for the price this stuff is hard to beat.

Great wire. 100% would recommend!

good welds achievable albeit with a fair amount of splatter that seems to be quite common with flux cored wires....but then again it could just be my welding and set up. non the less i'm happy with the end results compared to the last couple of reels i've used.

Bought this because it’s super cheap, expecting it to be terrible. Welds nicely with little spatter but has quite a lot of smoke while still being easy to see the weld puddle. Comes in a sealed packet with a little bag of silica to absorb any moisture. Make sure to have a good grip on the wire and keep tension on it while installing. My spool was almost overflowing with 1kg of wire not 0.9kg. It wanted to spring over the edge from the way it was wound after installing. If this is the case for yours the best thing to do is feed a decent length through the gun and trim it off. I think a lot of flux core mig wire reviews regardless of quality/price include user error in regards to their performance. The wire should be ran on DCEN (Direct Current Electrode Negative) not DCEP (Direct Current Electrode Polarity). Not doing this causes excess spatter and worse welds. Did a few test beads with it on some mild steel and it runs just as well as more expensive brands just with more smoke. My first task with it was welding some grey cast iron pipe to bodge my neighbours washing line pole which isn’t very suitable but managed to weld it no problems. Immediately bought another.

Great value for money and arrived on time. I used this outside in a field on a portable welder and found it did the job fine and was easy to carry as expected . . Size and appearance were as expected , it’s welding wire so not much to say there ! The quality is good with only one fault on the wire (a bizarre kink on the reel at one point only ) . Overall very happy and would buy again .

I'm new to welding so have not got a lot to compare to but this wire is great, I'm using it in my Sealy mightymig100, it seems to be making nice clean welds, it puddles well and leaves a nice bead, it spits a little but with any gassless mig this is the case, the residue left it east to wire brush off and reveals a nice looking and sturdy weld. as said - new to welding Home/hobby - automotive application mainly but I am more than happy with this wire 10/10

Welding wire 0.9 drum fine but do follow the warning, the wire is very springy and will unwind very quickly if not held by 2 hands whilst being installed by another 2 hands DO READ THE INSTRUCTIONS BEFORE TRYING TO LOAD INTO MACHINE

Bon produit

lo e usado para cambiar el hilo en la soldadura

Fil de bonne qualité, bon prix.

Alambre de soldadura de 1mm Actualmente a un precio de 23€ ✅ Alambre de soldadura de 1mm, incluye 1kg en total. Alambre adecuado para soldadura por una o varias caras, especialmente adecuado para uniones en T. ✅ Alambre tubular autoprotegido: adecuado para materiales oxidados, sucios y pintados, resistente a los residuos de aceite, apto para uso en exteriores y en diversos entornos.

Super