WHEEL CONNECT Wheel Display Hooks, for Hanging Rims on The Wall. Made of Solid Steel with Soft Plastic Coated. Accessories Included. Standard Size. Pack of 4.

They do the job and the red rubber is good quality. The screws that came with it had a head too big for the hole so I used my own woods screws. Would definitely recommend mounting these to the studs or a piece of wood attached to studs. They hold the wheels well but most are heavy at least 30lbs depending on size so I do not trust the sheet rock anchors it came with. I have them holding some 22 inch aluminum wheels that weigh about 36 lbs each.

Overall, this hook does the job and sits pretty well. Once installed, it looks sleek and functions as expected. That said, I did have to wedge a small piece of metal underneath to get the width set just right — a minor adjustment, but worth mentioning if you’re a perfectionist about alignment (guilty as charged). There were a couple of minor modifications required to make everything sit flush, but nothing out of the ordinary for anyone even slightly handy. Once in place, they feel solid — the key is to make sure you’ve got a good brace. Either tie into a stud or use a strong sheetrock anchor and you’ll be golden. Looking forward to seeing how well they hold up over the next few years. So far, it feels like they’ll stay put and do their job without a fuss.

Like

The build and sturdiness of these wheel hangers are amazing, I am using a BMW X5 and wheel as a display, and it definitely holds this heavy wheel with no hesitation. It did not flex. The install was very easy, it comes with a template. The design to mount the wheel is fairly intuitive, but you need clearance to tilt and get it to retain on the hook. You must use it on anchor bolts in concrete or studs especially. In terms of storage capacity weight it holds as described in the listing and the metal is thick and the rubber boots help alot. Would use again with no problem, been up there about 6 months so I believe the value is definitely there.

Only sits flat against the wall if attaching to the face of the wheel and not the backs for display.... Had to order another set (the smaller ones) to see if these work better. Didn't get them up in time to be able to return them either so I'm stuck with them. Unfortunate and disappointed in the product. Doesn't specify what size you need for 15"-20" wheels. Like I said it only fits on the face since there is a larger lip on that side of the wheel attached to the rim, vs the back. It would not take the lip of my 15 inch wheels and barely took the rear lip of my 20 inch wheels. It did like the face lip of the 20 inch wheel though. Screws also sucked they didnt want to go into a 2x4 so I had to resort to smaller and shorter ones made for wood.

I have no complaints. These worked great for my 15-17in wheels. Like other people have said, I didn't use any of the included hardware. I opted for 1.5in #10 screws through the drywall and into the studs. Super solid. I had to remove one of these months later and the rubber coating stuck to the latex paint. Pulled off a square of paint right down to the paper. Oops. I should have thought to place some wax paper in between. My bad.

I recommend these hooks. They are very sturdy and make sure you’re drilling into a stud in the drywall.

Really Saturday and holds up well

So far, so good 👍 Using only one of them to hold a 20" OE wheel that was on my 2018 Challenger. Fits perfectly and tight enough against the wall, it's screwed on my garage wall.

perfect, simple to mount , non marking. and virtually invisible with wheel in place. buy buy buy

The product is great, everything was included and instructions were clear. Just a warning however, research the surface you are going to mount into. I had a bit of trouble because I was mounting into mixed media, so I had to get creative and use some tapcons to get it to sit firmly; this is no slight against the product, this is a situational issue; this is more so just a warning to think ahead before you start installing using the supplied hardware if you're working with unique surfaces.

This is great if you screw it to a stud but using inserts will just damage your drywall. It was hard for me to put the wheels on the hook so I ended up not using it. Just sits in my drawer now and just wasted my money