KingstonFURY Beast RGB 64GB (2x32GB) 3600MT/s DDR4 CL18 Desktop Memory Kit of 2 | Infrared Syncing | Intel XMP | AMD Ryzen | Plug n Play | KF436C18BBAK2/64

Installed easily. comes in 2 packs of 2x32GB sticks. I made sure to use one package for the white slots for RAM and the other pack for the black slots so both dual channels had RAM from the same package. I know TECHNICALLY it shouldn't matter because they should all be from the same run, but I wanted to limit troubleshooting.Alienware (DELL) motherboards are notorious for not accepting aftermarket RAM.The first attempted boot my screen was completely black but I shut down and then changed which slot in the video card my monitor was plugged into and it fired right up.So now I have 128 gig working.I will note that the ram running at 2933 and not 3200 is a known issue with DELL and the Alienware Auroras once you get into dual channels of RAM so if this happens you didn't do something wrong and it is a known issue with no fix at the time.It is only about a 4 to 4.5% decrease in speed so it is going to be imperceptible to most everyone.Great product it worked and I am happy

This was installed on an HP OMEN 30L. Like many pre-built, the BIOS does not have controls for memory overclocking. You will have to study each manufacturer's specification to make sure you understand what timing and speed the memory is capable of in both JEDEC (usually 1.2v) and XMP (usually 1.35v). While you can get JEDEC 3200 from Crucial, I decided to go with the FURY Beast JEDEC and XMP at 1.2v at 2666 primarily to match the RGB design of the 30L. I understood the speed trade off.

Excellent RAM and great price! Easy to install in my HP 30L Omen Gaming PC. If you install the latest (9/21/2021) HP Bios you can fully utilize the 3200 MHz speed of this RAM.

ALIENWARE AURORA R9Tricky to install properly with the Alienware Aurora R9.The first time I simply installed the "Kingston FURY Beast 16GB 2666MHz DDR4" chip to an available slot along side the two existing 8 GB Hyper X Fury chips that were included with the original system. The system fired up and it worked ok for a little bit but then I started noticing issues with Window 10. I would try to create a folder and it would remain invincible until I forced a refresh. Happened over and over again. So I opted to reboot and bam! No boot.I then removed all the ram sticks and re-seated the new one. Powered the system back up while holding the F2 key to access the BIOS options. Navigated into "Advanced" > "Performance Options" and simply clicked "Optimized Defaults". Save changes and attempted to power my system back up. Works fine without the original FURY ram chips. I then added the recommended virtual memory under custom settings within Windows 10. Rebooted and the system powered on just fine.Next I shutdown the system and re-installed one of the original XFURY 8 GB 2666MHz DDR chips. Powered the system up while pressing the F2 key again to get back into the BIOS options. I did the exact same thing as before, "Advanced" > "Performance Options" and clicked "Optimized Defaults". Save changes and powered the system up. Checked for issues and none were detected. System was working as expected.Shutdown the system again and installed the last XFURY 8 GB 2666MHz DDR chip. Did the exact same procedure and the system has been working fine since. I rebooted multiple times to make sure and the ram issues appear to have sub-sided. I'll know for sure once I test games and other resource demanding content.So far so good.#########################I also noticed that the "Kingston FURY Beast 16GB 2666MHz DDR4" allowed me to select an XMP profile within the BIOS but the original XFURY chips did not. When I put those back in the system, the XMP option was no longer available and became disabled as a drop down menu option.

So here's the thing. Like others here, I used this RAM to upgrade an HP Omen 30L. They are absolutely correct that HP throttles RAM upgrades; you can throw these two 3200 Mhz sticks in, and you won't, right away, get 3200 Mhz even though the pre-installed RAM runs that fast.Enter Ryzen Master, assuming you have an AMD processor (Omens running Intel are out of luck unless you buy overpriced sticks from HP directly).Ryzen Master will allow you to set the RAM to its appropriate clock speed, even if the BIOS are locked down.TL;DR - if you have a 30L, get this RAM and download Ryzen Master. Best of both worlds - speed and lower cost.

They work great, they look great and they're perfect.One thing to mention is that they're tall.so for example I use a PCS FrostFlow 150 Series High Performance CPU Cooler on an ASUS® ROG STRIX Z690-A GAMING WIFI D4 and I use 2x32Gb ram Kingston FURY Beast RGB 3000MHz DDR4 CL16 and another 2x32GB ram Corsair VENGEANCE DDR4 3000MHz DDR4 CL16 (which is not as tall).Why? Because the Kingston FURY would not fir in the first slot close to the cooler, or it may fit but only if I lift the side fan to make space for it but it would look weird to have one under the cooler fan and the fan to be lifted on one side.So the Corsair fits there perfectly and they run well together being all DRR4 CL16 3000MHz, they're sloted to word in duals and they're super fine.Overall pefect.

Bought this as an upgrade from 16gb ram 3200mhz mainly for gaming. I have yet to see a noticeable difference in games (apparently you can get up to 10 extra fps on some of them) but it seems to have steamlimed my system and folders seem to open marginally quicker than before. Overall happy and would recommend.

decent but had to overclock myself even tho it says its preoverclocked.

solid low profile ddr4 ram kit never had a issues with kington kits

Funcionan bien si tu motherboard puede hacer uso de XMP y seleccionas el perfil que necesites.Los colores son vistosos así que tendrás iluminación dentro de tu case.Para manipularlos requieres el software de Kingston, de lo contrario siempre ciclarán todos los colores.