Z-Wave PIR Motion Detector Pet Immune, White (PIRZWAVE2.5-ECO)

I've had this working now for about a month. So far I have no issues with the detector, It seems to be well built and detects motion with no false detects or non-detect issues. Sensitivity is adequate, it has a jumper setting (see picture) for no-pet, small pet and large pet.. It also has a jumper for motion reset, which sets the default time to reset after motion is detected from 4 minutes to 5 seconds for testing. By default once motion is detected it will be four minutes before it can trigger again. It added fine to Wink by putting Hub in inclusion mode (Add Product > Sensors > Z-Wave sensor) then motion detector in inclusion mode (pull tab on battery or paper clip in small round hole in back). As others have said it detects motion and will send e-mails and/or texts. You can set up a schedule as to when it alarms, such as only alerting from midnight to 7 am as an example. I set it up to turn on a light, but as others have said Wink has no way to turn off the light. The robot functionality in Wink leaves something to be desired. Hopefully this will be addressed in a future update.This is not a Ecolink problem, this is a Wink problem. Also another thing I would like Wink to do is be able to group these devices so I can turn them on/off as a group. Example: Currently if I want to turn on 8 motion detectors when I leave the house I have to drill down into 8 devices and turn them on/off individually. This takes WAY to much time. As said earlier, Wink issue not Ecolink. As soon as Wink upgrades their robot software I will buy more. But as the software exists today (again, wink issue) adding and managing motion sensors is not implemented well enough to justify buying more of these. [7/31/2015 Update] Robots on Wink now work to turn things on if motion detected and off if inactive for X amount of time. So, I can finally recommend for Wink users. [11/2/2015) I was holding this down to four stars due to a WINK problem not EcoLink, I've increased this to 5 stars now that WINK has fixed their robots and shortcuts to allow me to turn on and off multiple robots from a single shortcut. This means, in effect, that I can turn on (or off) monitoring of multiple motion sensors (or other things) from a single shortcut. So I can finally hit one button to "turn on monitoring" and a single button to "turn off monitoring" making this product MUCH more useful as a whole house monitoring solution.

The "Ecolink Z-Wave PIR Motion Detector, Pet Immune (PIRZWAVE2-ECO)" has been running in my home for just under 5 months and has been doing a bang-up job with little to no complaints by me. It is a standard-sized format Z-Wave enabled motion sensor which I have paired with my Raspberry Pi/Domoticz z-wave home control setup. Pairing was simple: insert the battery and switch your z-wave controller into inclusion mode. It was found immediately with no issues and is reported in Domoticz (OpenZWave) as two separate sensors: the motion sensor and a tamper switch. The tamper switch is simply an on/off switch to advise when the case has been opened. The sensor is corner-mounted in my entry hallway approximately 9 inches (~22.8 cm) from the ceiling and points towards the kitchen/living room area however, as it does have a wide field of view it covers even the bedroom door areas. From its location it points down the hallway and through the galley-style kitchen and on into the dining area with clear line of sight; a total length of approximately 32 feet (~9 3/4 meters). I have the unit set to the highest sensitivity (a simple jumper connection within the unit changes this) which detects even a small movement at the far end of the dining area. Keep in mind the sensor is hard-coded with a 4-minute cycle time meaning it turns on then remains in the current state for 4-minutes before checking again. For me it is no issue however if you are looking for a smaller time frame this is probably not the unit for you. It also reports battery level and after just under 5 months my unit is still reading 99%. Not too shabby. I have my system set up to activate a hall light when movement is detected (only after dark and only between a certain time period) and it works like a charm. There is a slight delay of approximately 1-2 seconds at times though I believe that is due to the large distance between the motion sensor and the Z-Wave controller - the signal needs to be repeated to and from the controller to reach the unit. If I set up a light as a slave device the delay almost completely disappears. Overall, this unit suits my setup almost perfectly and I'll be purchasing a few more in the near future to automate a few more lighting scenarios.

Funciona muy bien y la duración de la batería parece que va a durar mucho. La conexión con SmartThings fue rápida y salvo por el problema de que su tiempo de refresco es mínimo cada 5 minutos.

I cannot test this as the unit is not compatible with UK/EU Z-Wave networks. Unfortunately, the frequency was not mentioned in the description when I purchased it. I would buy it if a UK/EU version was available.

It does the job, easy to interface. Using it with a Piper.

These are great motion sensors. Paired up very quickly with Smartthings hub and work great. Very quick and responsive. Great battery life so far. Used to have all Zigbee sensor that would constantly disconnect and these Z-Wave sensors are much better.

Llegó incompleto, ya estoy viendo la devolución