TOWOND Projector Screen and Stand, 150 inch Indoor Outdoor Projection Screen, Portable 16:9 4K HD Rear Front Movie Screen with Carry Bag Wrinkle-Free Design for Home Theater Backyard Cinema

I will be giving a presentation in a large dining hall in a couple of weeks. The hall has no screens for projections, and I need to be able to project large enough for people to see from about 80 feet back. Further, the entire East wall is glass with no drapes or other covering, so there will be a lot of ambient light - especially right after lunch at noon. I have a fairly bright projector, but I needed a portable projection screen that gave me at least 9 feet of horizontal display area. I selected the Towond 150" screen after reviewing it and others and checking the comments. This was a good choice. The Towond screen arrived packed in it's carrying case. The black plastic fabric case is 32" long x 6" x 7" with a carrying handle, and is quite light - their data sheet says 11.5 pounds, but it feels lighter. The case contained all the parts, a minimal pictorial instruction sheet (which was sufficient). The screen itself is in a separate, heavy-weight, zip-lock-type bag to protect the soft white polyester screen. Set up was easy by following the directions. The top-bar pieces are individually numbered and shown clearly in the instructions. The two vertical legs need no assembly - just loosen the friction locks and extend the vertical posts. I was able to set up and take down single-handed with no effort. Suggestions for the easy way (IMHO): 1. Set up the vertical legs approximately where you want the screen to be located. Loosen the clamp holding the three bracing legs against the center post and extend the bracing legs until the connecting parts between the bracing legs and the center post are horizontal. (Note - the safe way to open this is to pull each of the three bracing legs outwards.) Tighten the clamp so the bracing legs are firmly set. 2. Extend just the upper-most vertical leg pieces on both legs. (Leave the lower two extensions down.) 3. Assemble the cross-bar - follow the directions and ensure you have the bars in the correct order AND the two end pieces should have the larger through-holes at the extreme ends. 4. Remove the wing nuts and washers from the legs and set them aside. 5. Slide the screen onto the cross bar - take your time and avoid catching the fabric on the feeding end of the cross bar - don't get impatient and tear the material. (The material seems strong enough, but just take it easy...) 6. (one person can do this easily, but two make it real easy) Place one end of the cross bar on the post on one leg, then repeat with the other end - moving the leg as needed to match the bar length. Make sure both legs are stable and not tilted. 7. Fasten the bar to the legs with the washers and wing nuts. 8. At each end, fasten the top two velcro straps around the top-most leg sections (if you don't do this now, you may need a small step-ladder later). 9. At one end, loosen the next section and extend it (I was cautious and did this in two steps to avoid stretching the screen material. There is a marker line when it is fully extended. Tighten the clamps on both ends fully. 10. At each end, fasten the next velcro straps around the middle leg sections. 11. At one end, loosen the last section and extend it. There is a marker line when it is fully extended. Tighten the clamps on both ends fully. 12. Fasten the remaining velcro straps around the lower leg sections. 13. As needed, adjust the legs (and/or velcro straps) to remove any sag or ripples. (Note - I am only using this indoors, so I didn't use the ground anchors or the tie-downs.) Disassembly is similar, but even easier: 1. Unfasten all the velcro straps on both ends (all the ones you can easily reach - you can leave the top ones for later). 2. Slowly and easily, loosen the bottom leg section clamps and lower the legs, then tighten the clamps. Again - I did this in two steps to avoid excessive stretching. 3. Repeat with the middle leg section clamps. 4. Unfasten any remaining velcro straps. 5. I found it easiest to remove the cross bar and screen at this point, with the lower leg section still extended. 6. Remove the wing nuts and washers from the two legs and put them aside. 7. Remove the cross bar and screen from the legs. Note - ideally have a very clean floor/rug, or if you have friends helping, try to keep the screen clean while disassembling. 8. Slide the screen off the cross bar. Fold it down into a small enough area to fit in the screen zip-lock bag. 9. Disassemble the 5 cross bar parts and put them back in the longest bubble-wrap bag. (Note - rubber bands around the ends will make getting them in the bag much easier.) 10. Fasten the washers and wing nuts on the legs. 11. Loose the last vertical sections of the legs and collapse them fully, then tighten the clamps. 12. Loosen the clamp holding the three bracing legs on each support leg and collapse them, then tighten the clamp. 13. The two legs now fit in the two smaller bubble-wrap bags. 14. The three bubble-wrapped pieces (legs and cross bar) and the screen bag all now fit in the carry bag. So - I set it up in our dining room where the east-facing wall is all glass - clear and very sunny day here at 1PM. I set up the projector with the sunny display behind it and the screen facing the bright daylight. The projected display on the screen was sharp, clear, and plenty bright. Very satisfied - easy to assemble and disassemble - excellent image quality. The materials all seem to be good quality. The metal parts all seem solid and well made. The screen folds and unfolds and doesn't appear to take any creases. Overall - great product - exactly as described and works great.

Worked great. No issues. Top bar sagged a bit in the center but screen is so big it had no impact on projected image. Great value.

This product is good, the only thing is that the cross bar on top is not sturdy and sags. Easy to assemble and good quality.

Overall, I’m very happy with this projector screen. It was easy to set up, the quality is great, and it offers excellent value for the price. I would definitely recommend it.

Initial Review (05/16/2026): The image I attached is only part of the way up because my ceiling wasn't tall enough. I set it up by myself, but....it would have been easier with 2 people. Don't put the crossbar on until you feed it through the top of the screen. That will make it easier. However, its nice. Seems made well enough. I think I'll buy some better ground anchors just to make it more secure. I plan to use it outside for movie nights. And....the size is huge. My brain wasn't comprehending just how big it would be until I set it up. Looking forward to movie nights now.

Easy to put together and worked well, but tripod legs we were weak against weight of poles and screen. One already bent amd it wasn't even windy, barely a light breeze.

Great screen for the price.

This product is completely unusable due to a serious design flaw. The problem is not the screen material, but the frame itself. The center support arm is too thin, which means the tightening clamps cannot properly grip and secure it to the base pole. Because of this, the support arm constantly slips and cannot be locked into position. As a result, it is impossible to assemble the frame correctly and the screen cannot be set up for use. We followed the instructions and repeatedly tried to tighten the fasteners, but the support arm is simply too thin for the clamps provided. This is clearly a design or manufacturing issue and not an assembly mistake. I purchased this screen for events and presentations, but it cannot even be assembled. Unfortunately, this has been one of the worst purchases I have made on Amazon. I would not recommend this product unless the manufacturer redesigns the support arm and fastening system. A complete waste of time and money.

المنتج عباره عن قماش واعمده القماش جيد نوعا ماء الاعمده ضعيفه غير مناسبه في الاماكن الخارجيه نسمة هواء ترميها

Easy to assemble and disassemble. Great for hosting pool parties

Nice fabric for the screw , but the actual stands are build with poor quality metal, easily bent with the slightest breeze and even bends and squashes the metal when you tighten the screw points to set up the stand in the first place. Very flimsy.

Estamos muy contentos por éste producto, nos ayudó mucho porwue lo utilizamos para proyectar por la parte de atrás, y así no interfiere si se cruzan por el frente, la calidad es muy buena, sobre todo para lo que proyectamos, lo que tuvimos que adicionarle fue unos postes colados en una base de concreto y nos ayudo con el viento.

Good product great price