WaterWorker 25009 20Gal Vertical Well Tank, 20 Gallon, Blue

works well.

Arrived on time - we got a 3 day window for delivery and it came on first day, so that was great. Bigger than our prior tank, but plumber got the connections figured out and installed this quickly.

Way cheaper than big box stores. Good quality tank and works fantastic. Should last another 30 years.

This well pressure tank is well made, yet light weight. It was a great value.

Nice tank but a poor shipping container. Shipped only in a card board box with a plastic bag over the tank and plenty of room for damage in shipment. The tank we received only had a small ding in the bottom part of it. We got the 20 gal. tank as this is the size we use. It came pressurized at 38 psi. This is for a 40-60 well pressure switch. We do not recommend this tank for that sort of switch. Our pressure switch is 20-40 and we let the air off down to 18 lbs pressure before installing. We are getting 5.5 gal of water draw down from the tank before the pump kicks on. This is about all the water a 20 gal tank will hold, the rest is just air and the bladder inside. It is very important the air in the tank be set right before installing any water pressure tank. Always 2 psi below the low pressure point. Determine the pressure switch you have first such as ours 20-40, then there is 30-50, then 40-60. The inside cover of the switch should show this. The low pressure is when the pump kicks on, the high is when it kicks off. Thus the air pressure should be 18, 28, or 38 in the tank before ever installing according to the pressure switch. If the air pressure is not right it will cause the pump to cycle too fast, less draw down, rattling of water lines, and most of all expansion of the bladder inside the tank over time and the tank becomes water logged. The latter is caused by having too much air above the low pressure of the pump switch. We only get about 10 years use out of any these pressure tanks and they have to be changed. The weakest part of any of them is the elbow at the bottom of the tank. Its made of cheap cast metal which rust or corrodes over time and sometimes will block water flow to the tank. This elbow needs be brass or other non corrosive metal. This tank has a nice liner inside down to the point of the elbow and I suspect the elbow to fail after few years use, as there is no protection from rust or corrosion in that area. It would be cheaper for the company to discard all the waste of ink on the shipping box and use a plain card board box and pack this tank in styrofoam for shipping, the way this item is shipped is my only complaint about it.

The pressure tank was delivered quickly and after installation, it performed great. Actually a great product. I am pleased with it. I do want to note what others have commented on as well: the base was bent. It seems to me it would be a minor issue to insert a heavier piece of carton backing on the base of the shipping box, and therefore prevent this from happening. Of note: the bent base does not affect the performance of the unit, as it is the base of the pressure tank. However, it seems like this is a shipping issue that could easily be rectified for little to no additional packaging cost. Update: About 3 1/2 years after installation, the unit went bad. Would no longer hold air in the bladder. I called the company and within a week, a brand new pressure tank was delivered to me totally free of any charges. It was no hassle whatsoever to get a replacement sent. The company just wanted the serial number. No questions asked other than that. Good to know this company backs their product so well.

I purchased these as replacement tanks for our well pump. They have worked fine and were the same price range as the same gallon size tanks from home improvement stores. They are very simple to install (at least using PVC) the only reason I did not give installation a 5 is the description states they are pre-charged with 25lbs of pressure when both of the ones I purchased were closer to 40-45psi. The PSI difference would cause my well to momentarily lose all pressure prior to the pump engaging. This was a simple fix but was still an inconvenience. I should have just checked the pressure prior to installation. They have been installed for several months now and other than the first minor inconvenience there have been no issues with these.

Has one inch outlet has metal base not plastic decent price came before original date bladder was preset to 39 lbs for forty sixty pressure switch would buy again

Works great!

Awesome