LLT 4FT LED Vapor Tight Light Fixture 36W, Indoor Outdoor Commercial Waterproof Shop Light for Car Wash, Walk in Freezer, Garage, 2700 Lm, IP66, 100W Fl. Equivalent, 120V, 4000K (Bright White)

LLT 4Ft LED Vapor Proof Light Fixture 36W, 3500K (Warm Light) 2700lm, 120VThe light does not come with any kind of connection cord. You have to provide it. Most suitable would be an SJT or SVT 18 gauge, 2 conductor round wire cable. This is like the type of cord you might find powering your computer. Most can save money by salvaging an extra computer power cable and cutting the IEC side end off, and leaving the standard plug. If you need a cord longer than the standard 6 foot cord, home centers sell this type of power cord. Some of it is outdoor rated. To save money, you could even buy a 16 gauge outdoor extension cord (a 50 foot cord is about $15) and just cut off the receptacle end.The nipple in the fixture is able to accept a cord up to about 0.360 inches. That covers just about any kind of cable in the 16 to 18 gauge range (2 or 3 conductor). The internal wiring looks like it is about 18 gauge (remember this is a 36 watt fixture, large gauge wiring is not needed). After inserting the power cord, you make your connections (only the HOT and NUETRAL are needed; there is NO ground connection, so only a 2 conductor cord is all that is required), you turn the outer capture to squeeze the power cord to seal the fixture. LLT provides a removable "quick" connect block inside the enclosure, but you can choose to use traditional small wire nuts (not provided) if you feel that is more reliable, as there is enough room to accommodate them. The fixtures can be "daisy-chained" as power at one end of the fixture is brought to the other end of the fixture. Remember to seal the unused opening to maintain the vapor barrier, a small leftover piece of power cord works great for that.When I opened each of the access covers on the 7 lights I ordered, the seal lining the door came off (it had a spot of soft glue on the door itself). Fortunately it is easy to place it back in the recess side of the fixture. A flat-head screwdriver and a light touch to guide the soft seal places it back into its groove.I did not experience finding anything rattling around inside the fixture. Not sure how that could even happen as all the mounting screws and retainers are in a sealed plastic bag. I would recommend that you find better mounting screws especially if you are placing the fixture on sheet rock. The included anchors can easily spin out in sheet rock.The manual: The English measurement shown of 2.78" for the 850mm measurement is wrong, the correct conversion is 850mm = 33.46 inches.I do agree with others that the light output is very good, and that the diffusion of the LED lights is excellent. The stainless steel mounts are suitable for the very light-weight fixture, and can be bent slightly to adjust tension if they are too loose or tight. I have no doubts after mounting them that they will hold.Some may be wondering if the nipple ends can be removed and fitted with standard 1/2" PVC electrical connectors. It does not appear that that would be an option, as the base is molded into the fixture and has a fine thread. You would have to do some creative modification or find some kind of adapter.Very good value for the money.

Had two, standard garage lights in my garage, replaced for the second time now, then they both quit working. Grrrr. Ordered one of these. Install was easy enough. Although the existing electrical wire was centered, based on standard garage lights, I had to add some wire to reach one of the ends of this light. I'm not an electrician and not sure of the significance but the interesting part is that this light does not have a ground. I used the clips, successfully, they lined up with the existing mounting points for the old lights (where a stud was). Nice and bright. Only have the one in the garage. Seems to be more than enough light. I may or may not replace the other light.Once I'm comfortable with the light working for a while, I think I will order a number of them for my shop (it's a 40x40 shop) that really needs more lighting.

I got 3 of these. 2 of them were great, 1 was not so much. Overall these are pretty good lights, easy to wire, very bright. 2 of them were perfect, went up without issue and are working great. When I went to hang the 3rd one, I noticed it had something lose inside. I had to open up the unit, inside I found 6 extra bus bar screws and a bus bar. I sealed it back up, checked the bus bars to see if they were missing parts they were not. Then I started mounting the unit. It was missing hardware, I made due, then when I got it up and wired, I realized the light was bowed. All in all I was in a time crunch and made it work, but the extreme poor quality of the last unit make is so I can not give these lights 5 stars. But based on the first two lights these are definitely worth a try.

I really do not need waterproof or vapor proof lights, but these lights are very nice.I use these lights (2 ft. and 4 ft.) for my basement work and storage areas. I first bought some a few years ago and, when I needed to add another light fixture, I was glad to find them still available. That suggests to me that the company is still around and a making a successful product.These are great lights. First they are made to be hardwired and the hardwiring is pretty easy. They are also very light weight, which makes them easy to install over your head. Once installed the lights are plenty bright. And finally, they are quiet with no hum at all in any of my 8 light (I have other makes of LED fixtures that do buzz, and it can be annoying). Oh, when the switch is turned off, the lights have an slight afterglow that lasts for several seconds, which I find kind of cool

Amazing for the money! I have been looking all over for flush mount LED lights to replace my dual tube shop lights in my garage. I would be well over $600 to get equivalent or more lumens from most things on the market. I finally found these and ordered 2 and 2 power cords from another seller to make these a simple direct replacement since I have switched outlets installed already. The vapor tight fitting on the end was the exact size for a 16-3 power cord, and the light has connectors installed out of the box. I put my new cord into the light attached to provided fitting, put the provided brackets up and snapped the light in. It's definitely brighter than my old t12 lamps and looks even better. It's lightweight and the bracket are "flimsy" but as soon as they're screwed in they are more ridgid. No concern whatsoever of the lamp falling. This product was exactly what I needed and exceeded my expectations. I will be ordering 4 more to replace the rest. Also, the paperwork says it has a 2 year warranty.

Super easy to install Supplies lots of light for a workshop ( I put one on longest wall and three 2 foot ones on smaller walls. Eliminates shadows, protective cover in case I bash one accidentally and all four use very little power

Awesome light, easy to in stall

Great for garage/ workshop/ utility room. Nice even light. Not really vapour proof unless you seal the ends with some silicone caulk. You also have to provide your own rubber/ water proof wire for wet location usage. Connection inside light is not very strong, I used proper marrets to connect wires instead of provided connector.

The fixture is excellent and is installed on the soffit above the garage door. Is controlled by the door opener. Bright.

Did not light; sending it back.May still order another and hope it works.