Don’t be fooled by cheap copies! GraBarsUSA are the originals since 2012. Made and sourced in the USA. We support American families, charities, and communities. When we invented GraBars, we built the toughest, most over engineered handle available for your Jeep. We back it with a LIFETIME WARRANTY. We encourage you to compare the high quality of GraBars to the cheap copies - between their terrible welds and questionable materials, you’ll see why inferior copies are a fraction of the price! Only GraBars are constantly revised and improved based on customer feedback. The cheap copies just don’t compare to the refinement of ours. Easier to install, better features, far tougher hardware included. Your Jeep is worth buying the best for! These are a few minutes to install (no drilling!) and will become one of your favorite mods. Grab the originals. Grab the best. GraBarsUSA!
L**Z
I was unsure at first
I was unsure at first on what i was getting one screw was too short and the company called me and ask what screw and sent out new one very nice people to deal with i bought two sets of grabbarusa one for each jeep
L**7
Love these! So easy to get in my jeep!
A friend told me i had to get these. So i did. But instead of the black ones he got, I bought pink. They’re super cute and i like the pink, but part of me wishes i had gone w the black - black would blend in while pink stands out in my peripherals.I’m 5’4 and my jeep has a 2.5” lift on 35” tires. i like being able to grab these instead of my steering wheel or seat (super bad idea).
J**S
Great product
Great productPassenger side was a bit complicatedBut super easy to install
L**N
Grab bar USA
These grab bars are made very solid, sturdy and strong. Very nice upgrade to Jeep Wrangler JK interior. Rear installed very easy, like within minutes. Front install took some effort. I took out factory bolts and put in new ones in and out was very hard. Hard to get out the loctite jeep used on oem bolts. Very hard to try and get new ones to start. Finally got it after a bit of trial and error and dropping bolt in pillar but finally got it to loosen up and go in. The other side I learnt from my mistakes so I took out oem bolts, 2 pillar plastic pieces and took out sunvisor then it was easy ,nothing in the way and you can see bolt going in nice and straight tighten it in and out a few times with it lubed with a bit of clean engine oil on threads and WD-40 in holes went in so much easier. Then with easier movement of bolts took them out and reinstalled pillar pieces and then put in grab bar then reinstalled the sunvisor. Second handle took about 15minutes first one took about an hour.
W**Y
Rock Solid.
Love these.Was able to install the rear bars in minutes. The front bars definitely require more attention due to the dreaded A-pillar cover. Fortunately we were in the middle of election season so I had 10,000 card stock flyers arriving in the mail every day from various candidates and causes. It was just a matter of creating a 2"-3" tube from a flyer and sticking that into the A-pillar access hole for that bolt. It came out easy and didn't fall into the abyss. I did however ended up dropping one of the longer stand-off posts into the hole - I wrongly assumed it was too long to allow that to happen. I said several very bad words. But I was able to get it out by gently prying open the side of the A-Pillar cover and sticking a screwdriver in there with the tip covered in duct-tape, sticky side out. Worked like a charm. Duct-tape saves the day again!Overall, the quality is absolutely excellent. Rock solid. The design is very well thought out too, with the front handles bent to match the angle of the a-pillars perfectly in parallel. Also, when you're sitting in the driver's seat they aren't in your line of site, other than a little bit in the upper corners of the windshield. The entire piece is visually in-line with the A-pillars. Smart.Everything I add to my JK Rubicon HR is based on functionality. I believe that everything should have purpose on this vehicle. These have purpose, but also the beauty of the execution of these bars is a bonus. Buy with confidence.
M**6
Very solid product for 2018 Jeep Willys JK!
Arrived perfectly packaged, quite easy to install. A little pricey, but buy once and cry once as they say.I took the advice of others and stuffed some paper towel in the plastic trim piece, to avoid the bolt from falling into the abyss. Luckily, I was able to remove it without losing it from the socket.As another reviewer stated, the spacers are flat cut, so once you tighten it all down, the grab handle itself is only sitting on a few spots of the spacer. If the spacer was contoured to match the size and angle of the grab bar, it would seat on far more surface area. With that being stated, they are still very solid and an excellent addition.Another reason they are important, is to assist in lifting us into the vehicle and positioning us in the middle of the seat before actually sitting down. If you are capable of entering the vehicle in this fashion, it will save your seats. Most of us lift ourselves into the vehicle, then plop ourselves down on the edge of the seat and slide over to the middle position. In doing so, we are prematurely wearing the seat out, especially the edge. Just something to consider.Bottom line, quality product, little pricey, easy to install and fills a need!
K**I
Awesome jeep addition!!
I love this product. Super sturdy. It took me a little longer to install; only because I didnt want to cross thread the new bolts.I have a lift kit installed on my jeep and these handles make it a breeze to climb in and out.I would definitely buy again. Super quality...
M**.
Sturdy grab bars
I like the fact that they are made of solid steel and made in the USA. They are very easy to install, but you will need a 5mm allen wrench for the installation.
Trustpilot
1 day ago
2 weeks ago
