Hon&Guan 6" x 8FT Flexible Duct | Insulated, 3-Layer Hose, For HVAC Systems

I used this to replace damaged heat vents in an RV. As it's rated for dryers I felt it could handle the temperature of an RV furnace. it is fairly flexible and was easy to snake through confined spaces. The rubber coating on the outside should make this much more durable the the flimsy foil face plastic vent material. Easy to handle and install and so far works great.

Awesome! This is insulated so condensation doesn’t build up when venting outside into colder air. Our washer and dryer is upstairs and the vent go up the wall into our attic then over our master bedroom’s bathroom then vents outside. Well our old ductwork wasn’t insulated so during winter months condensation would apparently build up in duct work without our knowledge. Long story short one morning my wife was brushing her teeth and all the sudden the water that held been building up in duct in attic broke through the cheap aluminum vent and the drywall on ceiling then water came down into her sink. Lucky me not on her head but close! We had no idea condensation was building up in the dryer vent. We get it cleaned out professionally too every six month as we do tons of laundry with 5 kids! So the condensation had been building up fast! We live in a newer home over with over 4000 square feet but we never go into attic so would have never known old duct work was tearing from weight of water. Maybe it ripped from cleanings overtime Idk but point is this insulation duct seems to do the trick as you can just feel the difference in quality. It’s sturdy! Just so much better than the old tin duct work that always tears and rips when you try to install it with the metal clamp and the little screw. This insulated duct stays in tact and goes slides right on doesn’t tear. Still goes on with metal clamp and screw but because it’s a strong plastic or pvc covering whatever it is it goes on smoothly! By the way State Farm didn’t cover the $4,000 plus damage to roof and repairs to duct work as they said this was a maintenance issue! And yes we presented them with years worth of receipts showing ducts cleaning every 6 months still denied it so I paid out of pocket. Now only $4,000 grand some may say but for someone who never had a claim in over 15 years on house or multiple cars you’d think State Farm would of tossed me a bone here but nope. I know what’s all this have to do with simple review of a 20 dollar piece of duct tubbing! If your on the fence of buying the old school cheap tin duct for your dryer vs dishing out few more bucks for the insulation duct get the insulated duct! It will save you thousands of dollars potentially! If you have the condensation problems with dryer venting outside. Excellent duct work just buy this. Was delivered same day when I had to have old one replaced. Well worth it and it easier to clean doesn’t tear when taking on and off etc. Buy it!

Does it's job. Would by again

xTool has a 3 inch hose, so if you buy another 3 inch hose, you would expect them to be at least the same size and work with the same couplers. But when you try to use this hose with an xTool coupler, it’s several millimeters smaller in diameter, so it definitely won’t form anything close to a seal. The hose itself is fine and feels pretty durable. It is a thick plastic, but not rigid like the xTool plastic where you can actually turn the hose in a particular direction and it will support itself. I did find that the difference in diameter between the xTool hose and this hose is sufficient enough that you can wind this hose inside of the xTool. So if you can find a coupler that works with this hose and an xTool port, this might be a good solution. UPDATE: I added two more pictures. Because it slides inside the other tube, I cut the xTool tubing to make two ends that go into the coupler and still have enough of the rigid xTool tube to provide some control and structure. I think this will work if you just use this tube to extend your existing tube in the middle. In the pictures you can see that I removed a middle section of the xTool tubing and replaced it with this. For additional structure, you could add more elbows of the xTool tube at strategic locations around this tubing.

Very long enough to from outside to my dryer only thing is hole was too small but that was on me

Just received my hose and the jury is still out. They weigh heavier than the full aluminum hoses you get from a home improvement store. The outer coating though is much thinner than I was expecting. The product picture makes it look thicker, but in reality, it's paper thin. The inner foil is also paper thin. In saying that though, the outer layer was difficult to tear a little piece off the end as a test. It stretched, but never tore off. The hose also folds up as nice as it came. The hose clamps are a nice touch, but I would prefer wingnuts at the end instead of the worm screw. Also, as a warning, be careful when taking the plastic wrap off. My thumb went through it and got sliced on the wire sticking out. You may want to put a piece of tape or something on the wire so it doesn't happen while camping. Now the part I'm not a huge fan of and the 3 star review rating. Mine smell. Some reviewers say they don't, while others say they do. My plan is to use it with a diesel heater and figured the foil would be enough of a barrier to let any harmful smells through it. While I haven't used it with the diesel heater, I stretched them out in a bedroom and just have them airing out. I would say it filled the entire room with that plastic smell. Hopefully they'll air out enough to make the smell go away in a few days. So overall, they seem somewhat durable, they fold back up nice, and the hose clamps are a nice feature. The smell though is a bit off putting but we'll see if it clears up.

It works good probably better for a gas dryer I use it for my ac and it does seem to keep it a lot cooler but you will still feel heat come off the hose.

My prior dryer vent setup was constantly leaking hot and humid air into my home. I purchased the Hon&Guan Dryer Vent Hose, 16FT. It was a bit difficult to attach to the dryer and the exhaust piping in the ceiling because the flex hose just barely stretched over the metal connectors. But, once attached, the seal was secure and no hot humid air leaked. I am very pleased with the product and the price point.

De afvoer slang is niet 3 meter maar 2,5 meter

As advertised.

Mak renseigné, je suis censée avoir commandé deux tuyaux de diamètre 150 et je me retrouve avec 2 tuyaux diamètre 100 et n est spécifié quand on le commande.

Er zit geen aluminium laag in de binnenkant. Is alleen zwart plastic. Foto klopt dus niet. We hebben andere gekocht.

As described, used to direct hot air from diesel heater to roof top tent