iSANMATE PLA+ 3D Printer Filament, Pla Filament 1.75mm Rainbow PLA, Color Change Filament Dimensional Accuracy +/- 0.03 mm,1 KG Spool

This is a great filament! The print quality is astonishing on any settings and I can always rely on the adhesion to be perfect. The texture and deep color of this PLA makes this by far my favorite filament to print my Flexi Pegasus with. Everything always comes out looking and feeling great from test prints to final products. This is a must buy for any Flexi Factory model!

works very well in my Bambu A1 printer i have not had any clogs with this and it lays down very nicely and is good value for the price print quality is good

I was about to give this a great review, until I hit the tangles. This filament is not tangle free. I think I will rather look at something else in future.

The blue violet galactic color looks really good. A little glittery and semi-translucent. I’m on my second spool now. First impression after opening the package was that it was very brittle. Even after 6hrs in the dryer it broke pretty easily. (Couldn’t quite bend it 45degrees by hand before snapping). On the printer though it works great. No bed adhesion issues or excessive stringing that you’d usually associate with “wet” filament. Note: If you print directly from the dryer it seems to be sensitive to temperature change. Usually if I print with it from my dryer it will feed just fine during the printing since it’s rotating in the dryer, but once the print is done and it cools down, I’ll usually find that it snapped where it comes out of the dryer. Luckily I haven’t had it break in the middle of a print. I started drying it before printing, then throwing it on the normal spool holder for the print.

This rainbow filament isn’t just PLA+—it’s PLA+++. I’ve bought this rainbow spool more times than I can count because every dragon I print emerges like it just flew out of a fantasy novel with a flawless ombré glow-up. Layer lines? Don’t know her. Warping? Never met him. These prints survive kids, time, and epic dragon battles—and still look showroom fresh years later. If unicorns had a 3D printer, this is the filament they’d use.

I'd been wanting to try wood filament for a while but hesitant to switch nozzle sizes. Found a good deal on the iSanmate wood filaments so thought I'd give it a go. No regrets. And now I like the speed of 0.6 nozzles too. I started with the Baby Groot planter model at 100% in the darker wood. Looked great but too dark for Groot. No problem, I also got the lighter wood. Wife saw it and wanted it as large as I could make it. The dark model is at 100% and the light at 250%. I've printed 3 large so far (~ 9 hrs each) and had no problems with the filament clogging (0.6 mm nozzle). I did have one adhesion problem but in retrospective I should have noticed the skirt lines didn't quite mush together. I'm getting stringing, but I'm printing at 2x normal speed for Ender 3 and haven't tweaked retraction much since the change. I'm sure it can be reduced. My first order included 2 spools (one light, one dark) and 1 spool came damaged. The filament was fine but the spool was cracked in multiple places. No way it would spin on my rollers. I contacted iSanmate and they took care of it very quickly with no questions. I've got more ideas for this filament, so definitely buying more.

Nice flesh tone. No clogs. Smooth extrusion. Highly recommended for 3D Makers!

I've used a lot of PLA and this has to be bar far the worst. When I got the roll, it nicely vacuum packed. I get it all set up on my Qidi X-Max II. It extrudes fine, I usually purge a bit more than normal to make sure it's ready to go before the first print. I set the perimeters to the temps this brand recommends and started the first print. I always watch the first few layers to make sure everything looks ok before I leave and let the Printer do its thing. Everything looked good. I come back about an hour later and the Printer is still going but no Filament is coming out. I stop the print and take apart the Extruder thinking it was just a jam. Everything apart, I see that the jam had literally broken the Heat Sink in half from either pushing or a moisture pocket exploded inside it. I have pics to follow up with that. I tried using the High Temp Extruder that comes with the M-Max II and while it did print a couple things, they looked awful! It jammed frequently as well. Thinking it was the Printer, I took the Filament over to my Ender 3 Neo. Got everything set up and was able to get another couple of prints that looked like dog ****. It clogged on the Neo as well several times. I tried using temps from 190-230. Tried with the fan off and then up at frequencies of 25%. Nothing changed. I'm going to return it because this is seriously just unacceptable. I should have Isanmate reimburse me for the broken Heat Sink but I doubt they will. Don't buy this Filament. Don't buy this brand. You might regret it like I do.

Had a problem with the filament being a bit wet, had to run it through a dryer multiple times, still not perfect

El color es bueno, pero al momento de embobinar creo que no tuvieron la suficiente precaución de hacerlo bien ya que al parecer viene todo amarrado, espero no tener problemas para imprimir y no tener que estar cuidando todo el tiempo que se vaya a romper Edit: 10 meses después y casi 30 kilos después pedidos es un excelente material super confiable y funciona muy bien, me siguen llegando a veces mal embobinados pero no se atoran ni se rompen

Love this color and how it looks, ended up getting other transparent colors from isanmate

EXCELENTE CALIDAD DEL FILAENTO, SALEN HERMOSAS LAS LAMPARAS IMPRESAS, BUENA TEXTURA BUEN COLOR, SIN DATOS DE HUMEDAD.

Come da descrizione ottimo prodotto