BLACK HIGH TEMPERATURE HT SILICONE ADHESIVE SEALANT 70ml HEAT RESISTANT 300'C

Magic, Did what I wanted & more with my fingers, LOL Temp exceeded 300C Still looking good. Does not close & the silicon goes hard. It is very good in bonding & with stands heat very well. Very Happy. Pity it degrades after a year, I have applied it to my rear RHS car light unit, Zafira 2009B. Hoping this does the jo. will update later.

The inner glass on oven door came loose,so i took the door off,Then took the screws out holding the door together.Then i removed the loose inner glass,and cleaned the glass seal and the door .Then i put the black high temperature silicone round the seal and stuck it back together.Ithen put packing between the front and inner glass to hold the glass firmly in position. Then i put the screws back in.I left it 24 hours to set then removed the packing. Then put screws back in and re fit the door. The result was as good as new. I have used the cooker for a good month,with no problems. I would highly recommend this silicone if you have a similar problem.

Works well, promtly delivered I used in for fixing windings on electric motors where the slighly flexible product with a temperature rating of over 200 C was useful.

Fearing I would have to go to the expense of having my electric oven door front replaced after one side of it became detached, I carefully removed the screws to find that it was just the rubber "seal" that had perished. I ordered a tube of this Black High Temperature Silicone Adhesive Sealant through Amazon which arrived within a couple of days. I must admit, I was a little sceptical, but after removing the old sealant and replacing it with the new, I was very pleased with the results! I use my oven on an almost daily basis and am pleased to report that I have had no further problems. I feel quite confident that if and when the seal on the other side of the door perishes in the same way, I'll be able to fix that side too! (Not bad for a woman who usually has to ask her husband to "fix" things - and whose husband was "well impressed" by my workmanship!) Brilliant results from a product that "does what it says on the tube" which, if I'd have called out an "expert" to fix, would have probably cost me an arm and a leg but cost me just a few pounds, and there's still loads left in the tube for any future "sealing" jobs that need to be done.

Did the job glued the glass back into front of oven door

On first use, the tube with the nozzle allows you to distribute the sealant evenly. For any uses after that it becomes tedious to try and get any amount of sealant out of the tube. The nozzle can't be sealed once used so the sealant does what it does best, it seals. You then have to remove the nozzle and apply directly from the tube, but even this became difficult to do on the fourth or fifth use as the sealant cures. It's is a difficult product to work with and only worth using the first time in one go. The product does work but there needs to be a way to stop the sealant from curing in the tube.

My oven door became unglued. I tried it on my oven door. Yes it worked very well. Easy to use. Very good quality.

I needed to reattach my Bosch oven's roof liner. (The top & bottom of the liner are shown in the pics; a lot of area to be bonded!) . Couldn't screw it back as I'd inadvertently damaged the threading in the clamping screw's original hole. 🙄 I've many strong adhesives, but none that could resist oven temperatures. Googled & the only thing I found was the Technicqll. Though none of the other reviewers had used it to bond a roof liner, which is more load bearing than an oven door, I ordered it from Amazon & applied it to the areas of the liner that'd touch the oven roof, clamping it against the roof with some tight-fitting pieces of wood. Left it for 24hrs. (Needed to reapply it to one corner which I'd missed & leave for another 24hrs.) Some time after the cure time had passed I removed the wooden clamps & the liner was quite firmly bonded. 👍🏾 There was a sharp smell from the adhesive, but I'd expect this and so left the over door open after applying so it'd disperse. Obviously, as I've only just applied it, I need to actually *use* the oven & see what happens, but I'm quietly confident all will be copasetic. Based on its ease of use & minimal adhesion to surfaces you DON'T want stuck (i.e. the fingers), I'd highly recommend. (... If I don't report back after I've actually used the oven, one should assume that all *was* copasetic...!)

Hatte für mein Moped keine Ölfilter Dichtung mehr zeitnah auf der Tour auftreiben können weil die alte hatte es warum auch immer zerlegt. Habe das Zeug genommen und siehe da Ölfilter ist bis jetzt dicht und alles gut. Lässt sich auch gut wieder ablösen wenn mans nicht mehr braucht. Dann hatte ich Fremdluft am Lufakasten ausserdem weil die Gummimanschette gerissen war und ebenfalls unterwegs damit abgedichtet, Zu Hause angekommen, dann Reparatur durchegführt und Dichtmasse lies sich ganz gut vom Lufa Kasten entfernen. Als notbehelf nun immer unterwegs und in der Werkstatt dabei. Nicht ganz bilig aber tut was es soll

Acquistato per una riparazione del forno, a distanza di quasi 2 anni tutto ok. Consigliato

I used this adhesive after deliding a CPU. I was able to easily cut/form the supplied nozzle to the right hole size. The glueing application went smoothly. I doubt that I will be able to use the tube and nozzle.

bra

Elastische lijm zwart