wolfcraft Laminate Trimmer - Edge Banding Trimmer with Replaceable Blade for Clean, Flush Trimming of Veneer on Furniture Panels & Shelving - 4300000

Does what it is intended to do at a very reasonable price. It was much easier to use than I had anticipated and cleans up the edge much better than a craft knife. It has an angled fitting at the back which allows you to run the cutter easily along the edge of your panel. A good addition to my tool kit.

This was to be the first time I had used iron on edging. I wanted to do a good job and this tool seemed good value for money so I bought one. It took me a minute or so to work out how to use it. There are no instructions but the diagram on the packaging was sufficient to show how it should be used. It is better than just using a chisel as it pushes down the edging as it cuts away the surplus stopping the edging lifting as the blade cuts. A chisel or Stanley knife blade won't do this. The blade on this tool is just chamfered on one edge so it cuts exactly in line with the panel surface. A Stanley blade being chamfered on both sides will leave a very thin overhang which is just enough to catch and be damaged. The tool left a slightly rough edge easily fixed with sand paper. The manufacturers missed an opportunity by not explaining this on the packaging. As you cut the edging you need to press the edging onto the worktop firmly to stop the edging coming off. I found a better solution is to use a Stanley blade in a scraper held up a bit at an angle so the chamfer on the blade does not leave the edge a bit high.

I have always made do with a Stanley knife blade, but was making 16 large mdf doors and was persuaded by other reviews. I was using a paintable edging strip, which is quite thin, and this blade coped perfectly well with it. I set the edge of the strip level with the front of the door and trimmed the excess off the back edge - to be honest, the trimmed edge gave a better finish. I would suggest centring the edging strip on the edge of the wood and trimming both sides to get a perfect finish front and back. Pushing the blade ( rather than pulling it towards you) feels wrong at first, but it is easy to keep the tool completely flat to the face of the piece whilst maintaining just the right amount of pressure.

This seems to be a copy of what was probably a very good tool originally. Regrettably, who ever copied it seemingly didn't understand how the original worked and, as a result, what could have been a very good tool is now barely fit for purpose. What is obvious is, if the blade had been mounted on an inclined plane, you could then adjust the height of cut. This isn't the case, the blade is parallel with the base plate so no adjustment of fineness of cut is possible. Also, as noted by another reviewer, the blade doesn't seem to be especially sharp.

As some have said previously, the blade doesn't sit flush with the bottom surface of the knife that comes into contact with the melamine surface, it's about 1mm too high, meaning that after cutting the edging there's still about 1mm that needs to be removed. Ended up sanding that off (not ideal) and gave up using the knife after the first board and instead used a multitool I had but didn't think to use before buying this. Much more effective and quicker. I also found the blade not as sharp as I'd have thought it'd be, particularly trying to trim edging that's just above the height of the blade - it tended to push the edging down instead of cutting it. On the plus side, it did arrive very quickly and I got a refund after complaining about it, both thanks to Amazon.

Very sturdy tool to trim edge banding with a neat finish. So much easier and more accurate than trying to use a Stanley knife or blade.

This was my first time ever sticking edging trim. This tool is NOT sharp enough to cut. My edging was 0.5mm real wood vaneer and this still struggled. It also under cut, but luckily this was on a trial. I ended up using a stanley blade with new sharp blades and worked a treat. Don't waste money, everyone has a stanley knife. Use it. Oh and do try it as test, a few goes and you'll master it.

Some reviewers complain that this tool doesn't work. I can only assume they're not using it correctly as it's easy to use and works effectively. A bit of time (about 15 secs the first time you use it) working out the orientation for effective trimming depending on whether you are trimming on the left/right top/bottom of your workpiece and you're away.

Worst

Funkar bra

Alles prima, gerne wieder! Super schnelle Lieferung! Vielen Dank!

Randen zijn prima af te werken

Essayer d’abord de coller et couper un chant sur une pièce martyre, avec le bon angle et en étant régulier dans le mouvement on arrive à une coupe parfaite