CT9110 110-Inch Track Saw Track Guide Rail and Adapters

These are a fantastic, low buck alternative to the expensive name brands. Mine arrived without any damage, nice and true for each piece. The only issue I had was with alignment. You're going to need a long straight edge or level because you can't trust the ends to be square. In other words, do not butt them up against each other - leave a slight gap and use the straight edge to insure the two pieces are straight before tightening the rail screws. (Tip - try joining each side for the best fit - there was a definite difference with mine.) Also had a slight lip on one side of the joined section. It didn't affect operation in any way but was annoying - rectified it by JB welding a washer to the underside of one section that protruded past the edge ... thus preventing the lip from occurring. IMO, that's a small price to pay for such an incredible value. I actually plan on buying another set to keep one permanently in 110 in mode and have the shorter sections ready to go.

I'm impressed with these tracks. I have the Festool track saw and these work perfect. I had to tighten the knobs a little to snug up to the rail but that took 5 seconds. I have one track for the festool and making rips on longer pieces was a chore trying to line it up perfectly but with two, not an issue anymore. Used them yesterday and all went well. The cuts on the end aren't perfect but if you put in the top connector, just put a 6/8' level against them to make sure they're straight with each other then tighten the two sliding connectors. Once I did it, I moved them around, flipped them over...etc and they stayed true. Ripped about 80' in varying orientations and no issues at all. They feel heavy duty, even more so then the Festool track. They're definitely heavier so that's good. They also come wrapped with these two black molded end pieces...keep those. Once you take them apart, put the end pieces back on and that keeps them together and less likely to bang around or damage ends. All in all for $74 this is a steal. I also ordered the Melotough track holder for $40. It can apparently hold 4 tracks. So I'll keep these and the Festool on there so they're all together. Can't speak for other brands but I know Festool uses the same track as Makita, Milwaukee, Metabo and a couple other brands. Might have to adjust the knobs on your particular saw but it's VERY easy and quick. Better then spending double or triple on name brand. Happy cutting!

Used it on 12 boards so far. The track stayed put without needing clamps. Cuts were straight and my Makita saw slid smoothly across the joint between the 2 track sections. The double bar design connecting the sections protects the track from direct contact with the set screws. I'd buy these again.

4.5 Star. These work great with the Milwaukee Track Saw. I ordered two sets for the cost of a single Milwaukee 55" track. The anti tip feature works great. They are smooth gliding. I then cut one of the tracks down to a 31" and 24" track, great for cutting 24" and 12" stock. In total when doing this you end up with a 110" track, 55" track, 31" track and a 24" track. Excellent value. The half star is removed for the following reason. I am not 100% happy with the combined tracks for the 110" full length. From the box the ends are not cut square and hence when tight together they do not make a straight track. I am going to cut them square myself which should make this a non issue, however, I shouldn't have to. It's rather is that everything else being so nice they can't keep the QC on the cut ends better, it's such an easy task.

Bought this guide rail set for my Milwaukee Track saw and it rides so smooth and well. If you find it’s a bit loose, you can adjust the fit tolerance on your track saw. The Milwaukee one has some knobs in the base and I had to slightly adjust these. I haven’t tried the bevel anti-tip feature yet with it but “WEN” I do, I’ll edit my review. I also purchased the Jorgensen track saw clamps and they fit perfectly and the color matches amazingly if you’re ocd like that 😂

These work with any track saw I've used. I've ran Festool, Milwaukee, and Bosch on these tracks, and they're all about the same. Connecting the two tracks also worked well and gave me a straight line, so they're precise enough.

I don't know why you would pay for some thing more expensive. I can't compare it to the Festool or Makita, but I don't see a reason to. It worked really well. You will want clamps. (Spend a little extra on something better than the Wen clamps)

Is this the same as Fe2tool? No clue, I can't begin to afford their stuff. Does this work, heck yes! It combined with the WEN saw for it and the clamps makes cutting sheet goods down to consistent size a pleasure. No more crooked cuts. The quality is good enough for me. Pretty easy to combine the halves for long cuts, but if you were going to do a lot of larger and smaller sheet cuts I would buy a second section just so you don't have to mess with that very often. I do recommend the clamps made for it, even though I don't need them for every cut they do take the risk out of those longer cuts being exactly where you need them. I've used this on home projects with plywood, and for sign work using assorted materials and would buy again in a minute.

These arrived well packaged, zero damage from shipping, they had nice heavy plastic guards on the ends of the rails. The work just as they should. The build quality matched the Milwaukee tracks I already own. I can confirm the Milwaukee track saw fits these tracks like a glove and helped my make some long straight cuts.

Muy buena compra, facil de armar y cortes perfectos con mi sierra de inmersión wen, bajo ningún motivo corten el plastico negro, la sierra lo cortara en la primera pasada y quedara justo al filo del corte.

When I purchased these I happened to have a Milwaukee track next to it. The extrusion that the saw slides on is slightly bigger on the Milwaukee, such that when I dialed in my m18 track saw on the WEN tracks, it wouldn't slide easy on the other. So point being the cut strip is your line of cut so if you swap between track brands it will mess that up. Decided to go with the WEN for the way better price point and marginal decrease in quality.

Buena calidad

El producto llegó sin una de las partes de plastico que protegen las orillas de los rieles y la otra está rota. Afortunadamente los rieles no tienen daños graves solo un ligero raspón en una orilla. Todavia no he recibido la sierra de inmersión por lo que no he podido probar los rieles.