Original Wax Cotton Dressing Reproof protection for Clothing/Jackets

Excellent value and quality product. 500 ml in for slightly more than the Barbour 200 ml version. I opened the lid fully then rested it back on the tin before placing it in a bowl of boiling water. I do this to avoid pressure building in the tin from the warm wax, but put lid resting on tin to keep the heat in. I filled the bowl to about 2 inches below top of tin. Wax melted nicely after about five minutes. I placed my 25 year old Northumbria jacket on an Ironing board with brown paper under the jacket otherwise the Mrs would go ballistic ! After wiping any dirt off the jacket I started rubbing the wax into the jacket paying extra attention to the seams on the shoulders . Waxing the back of the jacket was easier to wax than the front due to the pockets needing a thorough going over . The wax itself looks identical to the Barbour version and is easy to apply. The results are amazing and have made my old jacket like new . I had to change the water in the bowl once while I applied the wax as I took some time to cover the jacket . I did put too much wax on the front of the jacket as I was getting over confident. However a few walks out in spring sun and a little rain soon solved that problem. Although there is no comparison to the Barbour wax jacket , and I absolutely love my Northumbria , the Walker and Hawkes wax seems just as good as the Barbour version and looks and feels the same .

Ordered the 500mL size. Was able to wax my jacket with two coats (pun intended) and still had approximately half the tin remaining. I think it worked out very well! Living in the UK in a cold house meant I wasn’t able to do exactly as recommended by Barbour but below is what I did. I put the tin into a pot of boiling water and let the wax fully melt. Be sure the level of the water is below the level of wax this way it won’t tip over. This can take 10-20 mins to fully melt in a boiling pot. I used a sponge to apply the wax. I submersed the sponge into the wax and let it drain the excess then I was able to apply the wax very easily and liberally across the coat, using long strokes and ensuring full coverage. I would avoid dipping the sponge then applying immediately as this causes big wet patches that soaks through quickly and is harder to spread. I then used a hairdryer to melt the wax on the surface to allow the wax to soak into the cotton threads of the coat, you will see the glazey wax go shiny as it melts into the fabric. I also used bunched up paper towels/kitchen roll and brushed across the surface to spread the wax as it melts in - this is really helpful to get rid of saturated patches. Hope this helps anyone trying it out. It’s really worth it and can give an old coat a new life.

Quick delivery. Looks good but haven’t used yet

I was very sceptical about re-waxing my husband‘s Barbour jacket, even when we started to melt the wax, I said I thought he would be better having it done professionally. How wrong I was! At first it seemed a bit of laborious job rubbing the melted wax into the fabric. It was doing the job, but going to take absolutely ages. After a short time, while he rubbed the melted wax into the fabric, I was ready with the hairdryer to keep the wax warm and melted to make it so much easier to work with. Others have mentioned about it taking eight hours, if you do it this way after an hour and a half, his jacket was perfectly waxed. It was a sunny winter day, so we hung it in the conservatory to allow it to dry. Once it was hanging, we checked it and any slight patches we just went over with the waxy cloth. He has since also re-waxed his waterproof waxed Stetson hat. Both items look absolutely brand-new. We would definitely recommend this product. . We bought the 500 ml size and have used approximately half of it. I wouldn’t hesitate to buy this again.

Applied easily to coat with cloth, section by section. Very pleased at restoring waterproof quality.

I bought the smallest tin and it works only as a touch-up for small areas. You will need a larger tin to re-wax a normal sized jacket. It works just as well as the actual jacket manufacturers.

The product is excellent if you follow the instructions as I did. (Warm water, hairdryer and air in warm conditions) However, the advert is deceptive. The tin is a lot smaller than shown. It is the size of a small tin of shoe polish. Not enough for a coat! They also could have included a sponge applicator as most businesses do.

Very difficult to apply as wax isn't very spreadable

Selbst bei Zimmertemperatur fest

Las instrucciones son fáciles. Síguelas y conseguirás una prenda de algodón perfectamente encerada. Ten cuidado de no excederte en la aplicación si la prenda es grande, porque, en ese caso, 200 ml puede que no te alcancen. Producto Recomendable

Easy to apply despite some doomsday scenarios in the reviews. Might be tempted to repeat the exercise on my Barbour coat quite soon though as the demands of Irish winters and other , three seasons are ... very demanding.

Utilisée pour entretenir une Barbour, cette cire est absolument parfaite. Moitié moins cher que la cire Barbour, les résultats est équivalent. La veste est comme neuve, c’est impressionnant. Il faut bien suivre les instructions du fabricant. Personnellement, j’ai chauffé la cire au bain marie jusqu’à elle devienne liquide. Il faut renouveler l’eau chaude régulièrement dès que la cire recommence à se figer, et chauffer au sèche- cheveux la partie de la veste que l’on traite. Ensuite laisser sécher au moins 48 heures. Le résultat est bluffant. Je recommande à 100% !

J'ai refait un "Duster" de taille 3XL de marque Driza-bone. Le première fois dans 20 ans! La tissue avait bien soif! J'ai utilisé un sèche cheveux pour chauffer le tissue pendant l'application. Je conseils de préparer un boite isolant avec plusieurs pains de glace pour refroidir le sèche cheveux entre sections si vous avez un grand article a traiter, autrement la sécurité de surchauffe rentre en action souvent. Si le produit se blanchis par endroit, repasse le chaufferette pour le rendre liquide puis frotter pour le faire pénétrer. Très bonne étanchéité retrouvé.