Question 1

When the pump is switched on by the floater, how long does it run?

Accepted Answer

If there is merely water in the sump pit, you don't need this powerful a pump. This 3/4 HP pump is for handling major water flowing into the pit. When that happens in our cellar, the pump runs until it out-runs the flow of incoming water.-- sometimes for minutes sometimes for hours. We have 4 sump installations in 4 buildings. When the water table (level of the ground water in the outside ground) is high, three of these systems pump a lot of the time and pretty constantly. We have 2 pumps in each pit so if one fails we do not get flooded. Each Pump (if more than one in the system) needs to have a check valve/ back-flow preventer so it will force the other pumps to actually pump the water up and out and not allow an operating pump to to just pump back out through the other , (not then pumping) pump. The should also be placed at different levels so they don't necessariy go on at the same time, thus reserving one as a kind of back up.  Of course, if there is really a lot of incoming water -- which we had when we first bought our house, it takes both pumps to handle the in flow and avoid flooding. NOw that we use the large diameter PVC piping, it works so much better that a single pump pof this size would probably be fine. It is best to pipe the pumps with real PVC pipe and in 1 1/2" or 2" size. This will increase the flow rate by  around twice as much flow as the skinny (1 1/4")  highresistance black curly-sided plastic pipe they often come with. Good luck and stay dry.

Question 2

when you say 'top suction' does this mean the pu,p must be totally submerged?

Accepted Answer

The pump does NOT draw water directly from the bottom, as some have stated.  If it did, it would draw in an dirt in the sump pit.  The question was correctly answered already:
“It (top suction) means the pump draws water from the top of the cast base vs. the underneath. Either way it is still drawing all the water from near the bottom of the sump basin. The top design just avoids sucking up dirt and sludge from the bottom of the sump basin. You can see the protected inlet screen built into the bottom black cast iron base.
This is a good pump overall.”

Question 3

how long is the power cord?

Accepted Answer

Just received my Wayne CDU980E.  I, too, was concerned with this question.  Power cord measures about 90-inches (7.5-feet) from where it connects to the top of the sump motor (which is about 11-inches above the bottom of the pump).  I can't find this marked on Wayne's literature for the CDU980E.

Question 4

Can this pump be hooked up to a battery backup?

Accepted Answer

It pulls too much current for most battery backups, a generator will run it fine.

ASIN	B00554SP3K
Best Sellers Rank	1,137,160 in DIY & Tools ( See Top 100 in DIY & Tools ) 935 in Submersible Pumps
Brand	Wayne
Colour	Black
Customer Reviews	4.6 out of 5 stars 3,319 Reviews
Flow Rate	77 Gallons Per Minute
Global Trade Identification Number	00040066214744
Item Dimensions L x W x H	26.7L x 22.9W x 27.9H centimetres
Item Weight	11 Pounds
Manufacturer	Wayne Water Systems
Material	Cast Iron , Stainless Steel
Maximum Lifting Height	5 Yards
Model Number	CDU980E
Power source	Corded Electric
Product Style	Submersible
Product dimensions	26.7L x 22.9W x 27.9H centimetres
Style	Submersible
UPC	040066214744
Unit Count	1.0 Count
Voltage	120 Volts

WAYNE CDU980E 3/4 HP Submersible Sump Pump – Cast Iron & Stainless Steel, Vertical Float Switch, 5,490 GPH, 5-Year Warranty

Details

Details

Description

Specifications

Reviews

Common Questions