Luxburg Universal Wall / Ceiling Projector Mounting Bracket Kit 43-65 cm holds 15kg 30 degrees Black

Bought to mount a Hitachi projector through a suspended ceiling in a church hall. It feels a little flimsy, but actually very well made with lots of options and flexibility. It is hard to imagine a situation where it wouldn't work. The main column is a bit narrow, making it fiddly to push multiple cables down, and bend them out at either end. However it does the job and was excellent value for money.

I’m using this to hang a large speaker to a ceiling. I’m using the 0mm drop version. As others have said the instructions are rubbish but as it’s a generic product to suit a bunch of projectors you’re probably going to have to get creative to make it fit your own anyway. On the plus side it feels pretty solid, clever design with a lot of fitting flexibility which can tilt up and down and left and right and comes with a bunch of fixings to suit most needs. I like the way that the projector part and the ceiling part are separate and then slot together on the ceiling with a couple of bolts to secure, makes fitting much easier. Very solid when fitted. I’d buy again.

Note: The 10-20cm does NOT rotate, you can adjust it higher/lower and then adjust the tilt left/right to level your picture, so if you want an offset make sure it says rotate. I assumed all mounts rotated, my bad, but it’s fine for my setup.I got the 10-20cm size, it comes with M4x12 and M3x10 size screws to attach to your projector - check what screw size you need for your projector.It doesn’t come with any instructions but it does come with a diagram which was a bit off-putting at first but you’ll figure it out. Here’s a rough guide of how I did it, if it helps (I have a Yaber 21 Projector):1. Spread out the arms and attach the E1 connectors with M & N (see photos).2. Attached the arms to the projector with the K1 screw & spacers.3. Then set up the mount according to the diagram (all the screws are H).Overall I think its pretty solid, good value for money and I’m glad I got it :)

Good product and price.

You get what you pay for with this, which sounds like an injustice given that once it's fully assembled and mounted, it actually seems quite sturdy. However, the instructions were basically non existent, they were more of a labelled diagram which lacked labels. Fortunately it wasn't too difficult to work out. My main concern with this product are the bolts that came with it. They appeared to be of a low quality and and possibly smaller than m6x60 bolts as 2 of them were simply too small for the holes I drilled, while the other 2 fit perfectly. Luckily I had some spare bolts laying around that I was able to use in their place. As far as adjusting the projector once mounted, it was quite fiddly and took as much time as mounting the whole thing, this could be my own lack of experience however.

The bracket was reasonably quick and easy to assemble at a reasonable price and does the job it was bought for. The bracket is being used to ceiling mount an aging Panasonic projector without any problems.

Installing the mount was simple enough - it came with all the components necessary, including concrete ceiling fixings and projector fixings. I only needed to purchase concrete drill bits since I was attaching the projector to a concrete ceiling.The quality of the mount admittedly isn't that great, not all the screw holes are threaded, so you'll end up with some screws that don't go all the way in (see 2nd picture). It's not worth overtightening them as it could damage the little thread that is there.Feeding the power and hdmi wires along the inside is quite a mission to accomplish, if you choose to do so then take careful note of how you disassembled it, because it can be quite tricky to put back together. Once it's done though it looks much tidier.The mount can be adjusted up or down, and the projector can be tilted up or down. Left and right tilting is a no-go here, so ensure the mount is lined up dead-on straight with the projector screen. If mounting on a ceiling, definitely remember to screw in the safety screw on the side as the clamp will not support the weight of the projector.In summary: Decent mount for the price. Don't hang anything expensive with it, get something sturdier. Don't overtighten screws.

Im really pleased with the bracket good finish and sturdy. Easy to assemble and loads of different options thank you.

I really like that the mount is set up to be modular making it possible to mount your projector is several ways. I was unable to use this mount though as I needed to mount my projector much closer to the ceiling and unfortunately this mount was not able to go that small.

Good sturdy ceiling mount. Could have had a feature for a protective cage to protect against balls as this is being used for a simulator

Par rapport au produit de la marque Epson son tarif est top et il supporte le poids de l appareil et plusieurs mode de fixation

Wie Beschrieben, die beste Lösung für meinem Beamer

Au top, installation facile, costaud, orientable et reglable dans tous les sensParfait