300mm T8 Tr8x8 Lead Screw and Brass Nut (Acme Thread, 2mm Pitch, 4 Starts, 8mm Lead) for 3D Printer Z Axis

It is okay. The threads have a variation every 4mms down the whole part .1mm. .1 mm I know small right? But 50mm later that is huge. Must be a die cut thread with a warn edge in one slot instead of a acme thread head cutter? Very weird error for a acme thread. Also seems deeper in some parts cut. I think this screw was cut with a bad set die or head cutter as the rod was broached. On the other hand! Nut was cut perfectly. And it also was perfectly lose on the screw. I tossed the nut on a old 8t acme I had and it fit nice. So kinda disappointed, the old 8t has less ware then the new one.

I like that this pair of anti-backlash nuts arrives in individual baggies inside of a larger one, especially since I only need the one for now. I have been impressed with the very tight fit between the two halves. This fit is critical since any play between the upper and lower contact flanges will represent the amount of backlash this nut would have. Since the fit is so tight there isn't any perceptible play between the two halves, which is ideal.I used this set to reduce the backlash on my lead screw for my longer lk4 pro. The factory nut was actually pretty good but this eliminates yet one more source of error and variance. I reused the factory mounting hardware so it was a direct replacement and easy swap.

There's not much to say about the leadscrew itself, really. It's pretty standard, with an amount of play that's neither exceptional nor remarkably bad, but one thing that I really appreciate: it was actually well packaged and arrived perfectly straight. It was in a box held in the center with foam pieces. 90% of the time I order linear motion parts they come in a plastic bag, or a tube if I'm really lucky, and often they get bowed by this. I had to leave a review out of sheer appreciation for a vendor that actually gives a crap if I receive parts in a usable state.

Disclaimer: I didn't use the included bushing. I installed it with a two-piece spring-loaded anti-backlash nut, which fits perfectly. Travels smoothly and there's no wobble at all. I had to trim mine down a bit because a 300mm version wasn't available, but that posed no problems.Mounting it into a spring coupler made for an M8 threaded rod was a little tricky, but I found that I was able to spread open the spring coupler by threading a screw into the "wrong" side of the outer clamp hole and tension it against a thin metal shim to force the opening apart enough to get the T8 screw in as deep as I needed it, then release the tension and install a grub screw in the center grub screw hole. Because the free side of the clamp is the only part that gets offset, it still left the lead screw perfectly centered with absolutely no visible artifacts on printed objects. Perfectly smooth walls!

Ordered these to use on my Creality CR-10S Pro V2 to help eliminate issues with the X axis gantry sagging when shut off. Parts looked very nice when I received them but unfortunately I did not discover until after I had cut one of the nuts to clear the frame on the printer, that the bolt pattern on the nut did not match the bolt pattern on the printer. This isn't a flaw in the part, the backlash nuts appear to be very nice, they threaded on to the lead screws very smoothly, but I wouldn't recommend them for anyone w/ a CR-10S Pro V2.Nothing in the description said they would or would not work for my printer, so it was on my to ensure that they were correct, and I didn't do that.

I ordered two and both were bent, one obscenely so. The nuts include were garbage as well with insane amounts of backlash. Do not buy anything from reliabot

Work as expected. The spring could be a little stiffer to help reduce the backlash on my CNC router machine, but the stronger the spring is, the more friction there will be. These will be right at home on things like 3D printers where strong opposing forces are not present. 3D printers will experience zero backlash with these. I recommend them.

Doesn't fit the Z axis on a 3018 CNC the blue coupling is mine.

Your browser does not support HTML5 video.  Oltre il costo indecente (pensavo fossero due a questo prezzo) è arrivata una barra completamente curva.Pensavo di andare sul premium e invece è inutilizzabile, perché peggio delle mie che voglio sostituire. La qualità sembrava anche buona, ma la curvatura vanifica qualsiasi altro pregio.Reso immediato

Leider nicht kompatibel mit dem CR-X von Creality da der Platz zwischen Gewindestange der Z-Achse und dem rechten Extrudermotor zu eng ist. Verarbeitung ist dennoch gut. Für andere Drucker deshalb brauchbar.

topp ,perfeckt