Ensenior 12 Pack 6 Inch LED Recessed Light, Dimmable, 6000K Clear White, 1200LM High Brightness, 12W 120V, Damp Rated, Ultra-Thin Canless Wafer Ceiling Light - ETL & FCC & IC

The media could not be loaded.  First of all, I have to say that this product is just excellent and the price is unbeatable. Something that it is important to know is that you need a lot of these because this is a conically directed light. So, they are super bright, but only in a very determined space. If you do your research online, you will find out that there is a determined space in between them. Therefore, for a big room, you will need several. I noticed that at my local hardware store, each one of these was costing in between $20 and $25. When you buy them in bulk, they end up costing between five and seven dollars and even cheaper.No, installation is a breeze as long as you have very basic knowledge of electrical installation and how an electrical circuit works. Excellent performance when paired with a dimmer. I strongly recommend this product.

I recently installed drop ceiling tile covers in our basement to replace/hide those old chalky ones and also replaced old can ceiling lighting which used a big metal housing above the tile.These lights are lightweight, the wiring is easy to connect into the junction box provided and it's literally plug and play. When connecting the wires to the adapter inside the junction box, turning the adapter clockwise while pushing the wire inside makes it very easy. It's in the directions but I didn't read them so it ook me a few times to figure out why the connections weren't holding. To remove the wire, you can't just pull out. You turn counterclockwise while pulling the wire out. Quite simple actually.There is a circle template provide to make exact cuts in the ceiling for the light to fit securely. In my case, to cut holes in the drop ceiling tiles, I bought a Goldblatt G05141 drywall circle cutter and set it to match the dimensions of the circle template. Easy peezy.For every tile covered, I put the old chalky tile on top. For the ones with a light, the chalky board rests on top as well but I didn't attach the light fixture to the chalky board and instead attached to the tile cover itself. The cover is thin plastic so when attached to the old board, the light would press up causing an indention in the plastic tile. The fixtures are light enough to where I attached them to the plastic tile itself using a piece of regalar cardboard for the fixture springs and it doesn't droop. For the junction box, I just placed that on top of the old tile. Hope that made sense.Some reviewers said the lights didn't dim enough. I bought a Lutron DVCL-153P-GR LED+ dimmer switch with a Lutron Claro cover. I don't know if the switch is on the compatibility list or not but there is no buzzing etc. It works great. Inside the switch, there is a dimming adjust "knob". In some rooms, I moved it to the lowest setting and it's very dim with the slider moved to the bottom and bright enough with the slide moved all the way up. For example, when I start my day in the home office, I turn on the lights at very dim and then gradually slide up during the day. For other rooms, I start out at the brightest setting. It's a very nice feature on that switch.For color of light. I'm glad I chose at least 3 options (3/4/5K). I chose to use 4K which I think is a nuetral light. 5K was a bit too harsh and 3K a bit to yellow for my taste. I think if I purchased the fixture with more options, I'd have a hard time making a decision. Lol. The cool thing is that you can easily change the color temp at any time. Example: I'm not sold on the neutral light in a bathroom so I may move the switch to 3K.The lights are more than bright enough and cover a good amount of area.For Customer Service. I cannot say enough kind things about them. One of my lights was missing a spring. The lights come with 2 springs attached to the light. In most cases, especially mine, you need both springs to securely attach the lights to a ceiling. I emailed support, they responded very, very fast. I explained my situation and they sent me out a replacement fixtuee immediately. I don't often get fast responses or resolution from many companies unfortunately.I recently bought an additional 4 pack of these same lights to finish up another room. No issues, they work great just like all the others.It's amazing how much easier these are to install vs those big metal can light fixtures.Hope this review helps others.

Purchased to place in a remodel. They work great, easy install and definitely elevated the look of the space vs the old school can lights we removed.

Lights were easy to install. Give off great illumination and brightened up our rooms significantly. Great product.

Easy to install and very bright I got nothing to dislike about this product so far so good

I installed 10 of these selectable temperature 4" LED lights into a home office. Install is very straightforward. Cutting the hole is easy with a 4.1" hole saw for your cordless drill. Here is the one I purchase for the job: https://www.amazon.com/dp/B07YY69BJG?ref=ppx_yo2_dt_b_product_details&th=1.I also purchased this to keep the mess contained, which worked very well. https://www.amazon.com/dp/B00ESWJU5W?ref=ppx_yo2_dt_b_product_details&th=1. Be sure to run your drill in reverse to protect anything that is on the other side of the sheet rock and to keep everything under controlWiring inside the junction boxes is a snap, thanks to the push connectors, but you'll have to provide your own junction box wire connectors for strain relief. I used this type https://www.amazon.com/Sigma-Electric-ProConnex-44694-Connector/dp/B00C3YCSUQ/ref=asc_df_B00C3YCSUQ/?tag=hyprod-20&linkCode=df0&hvadid=198079373928&hvpos=&hvnetw=g&hvrand=8154605891185787427&hvpone=&hvptwo=&hvqmt=&hvdev=c&hvdvcmdl=&hvlocint=&hvlocphy=9009782&hvtargid=pla-350781289325&psc=1.Be sure to remember to set your temps before you install so you don't have to pull them down to set the temperature switch. I selected 4000k for the home office. The springs have enough tension to snug them up flat to 3/4" sheet rock and there is a rubber gasket included for damp conditions.Once they were installed, they have functioned flawlessly (with one caveat). I didn't have any dud lights and they dim just as they should. The caveat is that you need to pay attention to their recommended dimmer list, which was updated in 2021 I believe, to be certain of compatibility. I looked at an old list, on which my dimmer, the Lutron Caseta PD-6WCL https://www.amazon.com/Lutron-Wallplate-Assistant-Incandescent-PDW-6WCL-WH/dp/B07SJJBTYY/ref=sr_1_7?crid=220XCZQVBVWJE&keywords=caseta%2Bpd-6wcl-wh&qid=1644862511&s=hi&sprefix=Caseta%2Bpd-6%2Ctools%2C112&sr=1-7&th=1 was listed but was evidently was removed from the new list due to customers having issues with it. Here is my particular issue. The switch operates the lights, does not cause flickering, is quiet and dims them perfectly, however when first turn the lights on they immediately come on, then go off for a second or two, then come back on. I spoke with Ensenior customer service, which was very responsive, and they recommend using a different dimmer, which happens to cost a hundred twenty bucks for the Caseta smart version, which is what I need. The non-smart dimmers were about half that. After spending sixty bucks for my current dimmer, I didn't feel like spending even more for one that may supposedly not blink. If I find the need for another dimmer elsewhere, I might swap it out, but for now I just wait for the start up sequence.My total amperage/wattage is well below the switches capacity, if you are wondering. Interestingly, I used the same switches in two other rooms but was using the fixed temperature version of these same lights and do not have any issue at all. So, whether it be due to phase, bias of the Extreme Low Voltage lights or perhaps a capacitor in the chain, it doesn't seem to effect the fixed temperature lights the same as the selectables in my case.All in all, given you have the correct dimmer or use a toggle, I recommend these lights, particularly for the price. I understand these type lights are pretty much manufactured by the same company and then are branded for the individual retailers, so I doubt they are any different than the ones at the big box retailers, except they are cheaper. I also cannot attest to the RFI issue, so that could become apparent at some point.

Great buy. Easy to install and work as designed. Look great too. What else can you ask for.

They worked beautifully and are very bright. I've only had them install for a month with no problem so I don't know how long they will last but so for so great. More than worth the money if i can get 10 years out of them.

Muy recomendable y de buena calidad

Took me about 3 hrs to install 7 lights in a blown wool insulated ceiling including crawling around attic and running power. Quick connects made the job much easier and the different brightness levels are a great option. Definitely recommend.

Strong material. Good quality.

Très simple à installer, bonne puissance d'éclairageavec 4 j'ai pu couvrir comme avec 6. La lumière est également plus homogènePrévoir assez de hauteur de plafond

This is not what I expect from recessed lighting. However, seller provided replacements promptly.