LISEN for 15W MagSafe Car Mount Charger,Magnetic Wireless Car Charger for iPhone 17 Pro Max Accessories,Magnetic Phone Holder for iPhone 17-12,Samsung,Pixel 9,Jeep Ford F150 Accessories,Gifts

This has been working well. The magnet is strong and the adhesive hasn’t budged since I put it on a few weeks ago, even in the summer heat. I like that there are two options for where to attach the base. I’m not usually a fan of vent clips since they sometimes make it harder to direct air flow, but I tried it out and liked this one. The vent clip has a very good design. It’s not going to fall off easily, which my last phone holder did all of the time. It’s not difficult to take off of the vent when needed, either. That said, I still prefer the adhesive base. The charging function works well. How well it works depends on the cord and car adapter you use. I use the cord provided and a good quality adapter that works with this item, don’t remember the output off the top of my head but the output you need is listed somewhere in the product description. If your charger isn’t working, you should take a look at that first probably. The charging isn’t super fast but it does work. I like the glow, it’s not too bright so it’s not distracting. It reminds me of Tron. The picture I have is from when I was setting it up and testing out the vent clip. Not super great resolution since it was dark, but you can see the glow. The little nob on the top left of my dashboard is the adhesive base. Overall, good quality for the price.

ABSOLUTELY LOVE IT! I have both installed on my dashboard and also the vent clip hooked to my driver's side vent. The Magnet is very strong and very study. My phone might shake a little while driving but it still remains attached to the magnetic mount. I love having it right beside my vent and can just easily pop my phone right on and off easily. The provided charging cord is long enough to go around my steering wheel and hook up to the vent mount. If I'm not in need of charging then I can easily just unplug the cord.

This was recommended by a you tube review. I bought a couple of cheep dash board mounted phone holders and they were not good so i decided to do a deep dive and find something that would work . This is it, its the best bang for the buck that you are going to find. It holds my I phone great and it never falls off even when driving over rough roads, chuck holes etc. The phone magnets to the mount instantly there are no goofy clips or clamps to mess with. The mount between the vent and the phone charger pad is good quality and dose not come loose, it uses a ram style ball and that is adjusts easily, it is short so it dose not stick out away from the dashboard.The short profile is out of the way and it doesn't move around while driving . The built in charger works fine, its really nice that i don't half to plug the phone in to a cable. I just plop the phone down on the magnet and go. I installed the mount in my work truck but will buy another one for my car I would highly recommend this to any one looking for a mag safe phone mount.

I just got the LISEN 15W MagSafe Car Mount Charger today, and I’m already really impressed. The installation was incredibly quick and easy—I had it set up in just a couple of minutes with no hassle at all. I’m using it with my iPhone 16 in my 2010 Honda Insight, and it fits perfectly into my setup. The magnetic hold feels very strong right away—my phone snaps into place securely and doesn’t budge, even on rougher roads. It’s also great not having to deal with plugging in cables every time I get in the car. I’ve only used it briefly so far, but the charging seems fast and consistent, which is exactly what I was hoping for. The design is sleek and compact, and it doesn’t get in the way while driving. So far, it’s been a great purchase and a really convenient addition to my setup. Looking forward to using it more!

Update #2: I received an e-mail from Lisen in response to my inquiry. The rep said to make sure the charger that plugs into the cigarette lighter has a minimum 20W output. In review of the Samsung "Adaptive Fast Charger" I was using, nowhere on it does it state the output wattage. So I borrowed an Ainope 36W charger and tried it. This completely resolved the problem. With the 36W Ainope charger, the phone now charges on the Lisen magnet Qi mount with no issues. I see that the instructions supplied with the Lisen Qi mount charger do state that the output charger needs to be a minimum of 18W. Conclusion: The Samsung charger I was using has an output wattage of less than 18, causing it to be incompatible with the Lisen magnetic Qi charging mount. I suspect that many of the other reviewers who experienced this same problem were also trying to use output chargers that have less than 18W. I have updated my rating to 4 stars. Minus one star because at the time of my original review, Lisen's hyperlinks to both their "support" page and to their "contact us" page took me to their product sales page, which was a bit frustrating. Otherwise the response and service from Lisen was great. As both a phone car mount and a Qi charger, this product is highly recommended with the use of a compatible output charger. Many older vehicles have lower output USB ports that won't work, and many older cigarette lighter chargers do not have enough output wattage to work. Back when I purchased my previous phone, a Samsung S9 Plus that came with the cigarette lighter charger I was trying to use, 10W was considered to be a "Fast Charger," but that is not enough juice to support this Lisen Qi charger. Update #1: I see that other reviewers have had the identical problem I am having. I used the Lisen product support link on Amazon, which takes me to the Lisen website *product sales* page (not to a support page). While on the Lisen website, I found and clicked on the "support" hyperlink. It also takes me to the sales page, not to a support page. Then I clicked the "contact us" link, which also takes me to the same product sales page... not to a contact page. I found a support e-mail address on the product box and sent an e-mail describing the problem. In reference to my original post, the Lisen phone number I called is the one posted on Amazon. I got an answering machine and left a message with my phone number and requested a return call. We shall see how this plays out. While my phone is mounted to the Lisen wireless phone charger Model 2E778, which is connected to a Samsung Fast Charger plugged into my car cigarette lighter, the charging starts, goes into turbo charging mode, then the charging stops a second or two later, then this cycle repeats over and over again never ending. The Mount attaches securely to my car vent. The magnetic mount is strong. If I can get the charging function to work, this would be a good product. I am using a newly purchased Motorola Edge + 2023 with the circular magnet applied to the outside of a Poetic case. The Poetic case has only a thin clear piece of plastic film on the backside and the circle magnet is attached to the plastic film. There is no thick plastic case that the charging has to penetrate through. Troubleshooting steps taken: I used the Lisen supplied USB cable plugged directly into my phone and the car charger. Charging worked normally with no issues. I placed the phone (in the Poetic case with magnet installed) on two different non-magnetic Qi chargers in my home. Charging worked great on both without interruption. I slid the backside of the phone around on the Listen charger to make sure I have correctly located the circular magnet and confirmed the magnet is correctly positioned and installed. If the phone is moved up, down, right, or left, there is no charging connection. On the sweet spot where the magnet is installed, charging starts, but then cycles on and off repeatedly. I called the manufacturer and left a recorded message explaining the problem and requested a call back. I will update this review if the problem is resolved.

This is perfect for the car. I love that I can charge my phone and see it hands-free too. I bought a plug in for the lighter and it all works well without wires all over the car. The magnet is strong and the fit on the car vent is stable.

The Good ----------------------- + Really strong magnet + Multiple mounting options (vent or adhesive) + Adhesive mount is very flexible in its design that would allow it to fit in a much wider array of places compared to others + 15W fast charging + Ring light on charger can be useful for finding it in low light settings The Bad ----------------------- - Haven't found any yet The Nitpicky ----------------------- = Took me a little bit to figure out that you have to rotate the base to extend the hook for the vent mount, instructions are mostly just a QR code for a video Thoughts ----------------------- I previously had an ESR magsafe charger for my car, but the plastic bit that connects the base to the mount broke and there's no fixing that. Not too broken up about it because the ESR charger was always hit or miss whether it would actually charge my phone or not. Sometimes I could be driving for 30-45 minutes and it would only charge my phone 1-2% when it wasn't even doing anything (no GPS, no CarPlay, nothing). I tried different cigarette port adapters, cables, with and without a case, even more than one ESR charging base and every time the same thing. Even across multiple phones when I upgraded my iPhone 12 to a 15. So this time I went in search of something different and settled on this. Only had a chance to use it on a single trip as of time of writing, but after I figured out you need to twist the base to extend/retract the hook for the vent mount, things went pretty smoothly. The magnet is pretty strong, so it won't be going anywhere during normal driving. Unlike the ESR I had before, this time even on a relatively short trip of maybe 10 minutes to the grocery store, it had already charged the phone by around 1-2%. As long this behavior is consistent, I'll be happy. I also prefer this vent mount to the old ESR one. The ESR was like a clothespin that you just "clipped" onto the vent flap, while this one hooks around the back and then you tighten things up so that it's pressing against other parts of the vent to provide additional stability. The adhesive mount is also interesting how it can be made to fit a much broader array of surfaces compared to most mounts. Suppose the drawback would be in finding replacement adhesive pads if you ever need them. Edit 2/8/25: Still so far so good. Unlike the ESR charger, where charging was hit or miss, this one is working consistently. I've noticed that, unlike with the ESR, I get the charging screen with the circular graph of battery charge every time I attach my phone to this charger. Edit: 2/23/25: Probably the last update as the device is still working well and I have no new issues with it. I don't usually like to drive at night if I can help it, but the light around the charger can be useful for letting me know where I need to put my phone.

Works great, and has a strong connection to the Pixel Snap magnets in my phone. I've used the air vent connector and it's extremely stable in the car, so there shouldn't be any fear of your phone falling off on bumpy streets. It's also very compact which is very nice. There is a blue light ring on it as well which is cool during night driving. However, it does not transfer any data so if you have wired car play/ Android Auto you would still have to plug in the phone.

good and strong when you use it as car holder

Excelente la carga no es muy rápida pero funciona bien...

The magnet pad area is very good, solid and efficient. I used it on the Mazda3 (2012) with the adhesive method. Using an iPhone 16 ProMax, which is heavy, I could adhere it to the right side of the console, and angle it for great access and visibility. Every time I snap the phone in place, and even though I use a compatible leather case, the attachment feels really solid. It has never failed, no matter the road condition and driving style. I can freely rotate the phone at 360 degrees. The adhesive is very strong. I had adhered it on the left side initially, then slowly removed it, deciding to try the right side instead... It still adheres very well, and is totally solid about 6 months in. No concern at all about the adhesive. This is a top product. The only thing that exceeds it is the high level of customer service I experienced (when I had questions about the placement of the product on the dash). The team is amazing, they clearly want to be the best at what they’re doing, and I think they succeed with their amazing line of innovative and quality in-vehicle phone holders.

جيد عدا ان الاسق ضعيف يجب شراء دبل فيس للتثبيت

Stabil und einfache zu installieren, sehr praktisch in der Anwendung