128dB Dual-Tone Car Horn Kit Compatible with Honda and Acura | Honda Accord horn replacement uses interchangeable Honda/Acura plugs; 128dB high/low tones install without cutting.

Installed this on my daughters 2024 Hyundai Kona. Installation was very easy and having the options of two different sounds was nice too. We went with the low sound. Word of caution, you will have to pull the front bumper to replace this.

Saved $650 doing it ourselves vs the stealership, who quoted $160 for these two horns and then 3 hours of labor (took us 45 minutes having never done it in our backyard with a screwdriver...). They fit and worked perfectly for our 2011 Escape.

Great horn for my 2008 Ford focus.fit perfectly with the connectors they provide in kit. I used the "low" horn and it is as loud as factory horn.id buy this kit again if I need to. My old horn sounded sick when I tried to honk it(turned out it was full of water from all the years of rainy driving)so I replaced with this,and I have a normal horn again.

Worked straight out the box plug and play, it sounds loud only issue i had is that for my make and model of my vehicle (2023 Hyundai ELANTRA sel) i had to remove the whole bumper. But after that it was easy to install it even had different connections for if i had different type of connection and i say it beats the time and money the dealer shipped was gonna charge me so i say it was a good buy

Just replaced my single factory horn on a 2023 Ford Escape. The horn is located on the radiator support inboard of the driver headlight assembly. This headlight assembly has to be removed in order to gain adequate access to the horn mounting area. In addition to the two 10mm bolts on the top tabs of the headlight assembly, there is a third 10 mm bolt on the underside of the assembly near the left front fender that has to be removed. The headlight assembly can then be wiggled/pried out (use plastic trim tools, and slide it a bit toward the rear). Once the headlight assembly is out, there is ample room to work. After unplugging and removing the factory horn, mount one horn from the kit in the bolt hole vacated. There is another painted bolt with a thick washer just forward and below this location (bolts through to the plastic radiator support) which can be removed to install one of the brackets supplied with the horn kit. Mount the other horn to this bracket, cable the two horns together using the supplied harness, and pivot the second horn back it so it almost touches the first one. Both horn openings should point as near downward as possible. This will provide just enough clearance to reinstall the headlight assembly. Then plug the harness into the car's horn plug. Tighten all bolts, ensure the wiring plug is secure, and wiggle the headlight assembly back into place; note the bayonet mounting clip on the front of the headlight assembly that fits into the slot in the front fascia. The horns are loud, easy to mount and wire using the supplied hardware, and fit just fine. They're definitely an improvement over, the single factory horn.

This was a great replacement for the original horns on my Elantra that went bad. They sound loud and a great low tone for the price.

Just put them in. So far they work great. Sounds louder than the old ones. So they don't sound weak. Easy to install. Great buy highly recommended

Fit our 2005 Camry perfectly. Nice and loud, much louder than the factory horns.

Uno de los conectores del Arnés no hace contacto correctamente se saco del Housing, tiene un falso contacto.

Easy fit and sounds so much better than the standard Ranger horn

For whatever reason, FORD decided an horn that sounds like a kids toy on a 2.7L V-6 Ford Edge is acceptable. I beg to differ. If/when someone needs waking up in traffic or I need to make someone aware of an imminent danger, I want them to hear me. That issue was solved with the installation of the NEOGET horn. It is loud ! And, it sounds like a truck horn. It was extremely easy to install. However, I didn't think much of the "how to" videos on YouTube so, instead of taking a headlight out to get to the mounting position - I jacked up the vehicle, took the wheel-well covers off and that gave me very easy access to the cavity below the battery to remove the 'micky-mouse' OEM horn and substitute it for the NEOGET horn. Beginning to end, the installation took less than an hour, probably closed to half that time. final verdict - it sounds GREAT.

I initially purchased this version of the NEOGET VW/Audi horn, and it fit perfectly on my 2018 Tiguan. The sound is great, nice and high-pitched, very similar to the OEM horn. In colder weather it does hesitate slightly, but overall it performs well and sounds clean and factory-like. The seller was also very kind and sent me the other VW/Audi horn version as well (the 4.6-star one), so you can find my review for that model there. Overall, a positive experience and great customer service!!

Fits 2017 honda civic. Sounds good but the main connector that connects to the harness doesn’t click. It works but it might come loose with time and vibration. Lets see