RS120 ARGB 120mm PWM Fans – Daisy-Chain Connection – Low-Noise – Magnetic Dome Bearing – Triple Pack – Black

used these for H6 flow case, work great, look great. Daisy chain built into the fans so you only have to use 1 ARGB and 1 PWM if you want to you dont have to daisy chain you could use them separate if needed. Max fan speed was about 1800RPM on full power on the 140mm. Since it is forcing me to review both the 140mm 2 pack, the 120mm 3 pack, and a single 120mm fan all in one because they are different variants, i will mention them as well. the 120mm fans are great, a little loud when at 100% but the RPM max is 2100-2180, so yea its not going to be quiet lol, they are PWM 4 pin, also have daisy chain option built in, one of the products i forget which maybe the 3 pack came with 2 ARGB and 2 PWM extensions which can be useful, i had to set up the fans "sideways" not that you can tell, because the wire placement was in the way for the wire channel when upright position. What i did so the fans were not on top of another's wires was took the wires out the little holder and that gave just enough slack to not have the wires under the fan and the wires were no where near the fan blades after. I went from nzxt to these, nzxt had a lower rpm rate on both 140 and 120s, therefor was more quiet, but i am fine with the noise, i have a headset on 90% of the time im using the PC lol. So crank away. 5 star on all products, would recommend, good quality, high RPMs, ARGB!, style is great, would 100% recommend the 120mm fans to put on a radiator as they have a high rpm and push pretty good, the 120 fans on my cooler master max rpm is like 1800 so i almost want to swap them for the extra pressure.

I replaced 6 older Corsair case fans with these. They are very quiet and work very well. With 3 setup as intake and the remaining 3 setup as exhaust, they keep the case cool even when running high-demand applications. Installation is relatively easy, though the daisy chaining can be a bit confusing as the cables are a probably longer than necessary and it's easy to lose track of which cable end plugs into which other cable end. However, once installed and the cables are properly tucked away/managed, they work great. I don't really use the RGB features (I just leave them a single color), but the LED's are bright and work well when plugged into the motherboard.

Bought 3 of these to replace the Thermaltakes which came with my CPU cooler when Thermaltake refused to RMA just the fans. Even though I bought these "used" (aka repackaged), they came in good condition and had all the parts & pamphlets that mattered. They have a high static pressure (nearly 3.5mm H2O), and are rather quiet even at max speed. Keeps temps low even on my monster 14900k. One fan did come with short cables (~3 inches), but since I chained them all on a radiator the length didn't matter. The RGB works fine, and syncs with my motherboard's other JARGB1 via OpenRGB. Looks no worse than the originals. Will update in a few months whether the quality stays high.

These are really nice fans. Airflow and rotation directions are clearly marked. They work well with motherboard ARGB control or with a discrete ARGB string controller. The PWM and ARGB connections can be daisy chained to control 2 or 3 fans from a single PWM and ARGB header. The colors look great and definitely get bright enough. They move plenty of air when they need to, and are whisper quiet when operating at low and even moderate speed. I've used them in two different cases recently with no problems, they fit well where a 120mm x 25mm fan is expected to go. The three fans come with standard black mounting screws and with two additional ARGB extension cables and two additional PWM extension cables.

Replaced a couple fractal aspect 120s with these 140s and my CPU temp at full load dropped by 5+ degrees, from mid 80s to high 70s (5800x3d with a Thermaltake Fs 140). They’re just about dead silent at idle and audible but tolerable at higher RPMs, no annoying whine or whistle with these just a rush of air. Wanted RGB for the kids and the colors and diffusion look fine to my eye. These are pricey however they don’t have rubber pads at the mount holes and they have comically short power and RGB cables which caused an additional purchase of 4 pin extension cables. A nice long RGB cable on my 120mm thermalright cpu fan had a daisy chain part to it and is the only reason I could finish the build without RGB extension cables. So these aren’t perfect but they’re fair quality with decent overall performance. Hope they last!

I've had these fans now for like eight months and they are absolutely perfect. You can change the color on them, the software is super easy to use, and they just look awesome in my setup. If you're on the fence about getting them, I highly recommend them. The only thing to consider is that it does not come with a hub to connect all the fans, you gotta connect them to the motherboard/daisy chain them.

very nice fan set, super quite good air flow, the colors are nice also, installed a few days ago and happy so far cane with mounting screws and extension cord for lights and fan, clean setup

corsair fans what else do you say. work great, quiet, and shine bright. pwm and 3 pin argb you dont need a corsair controller and they work with any rgb software.

good quality

ممتازة جدا سرعتها عالية وممتازة للتهوية

Decent fans. RGB colours are quite nice, not too bright. Air flow is also good, default speeds are a bit loud. Do need to adjust them via mobo or otherwise have decreased temps in my mid tower case by a fair amount. RTX 5070ti idle before at 40 degrees down to 29 degrees C. Cpu idle 31 degrees down to 27 degrees. RTX full power was at 72-76 degrees depending on game, with fans installed now down to 64 degrees C. Internal case temps dropped a considerable amount too, about 10 degree drop overall. The cable length is disappointing, could do with more length and more of a insert to place cables which aren't used. Bought a separate PWM Fan controller to connect all together. Probably get more out of them if stuck on full speed but the sound isn't worth it. Pricing was ok due to black friday deals. Installation was ok, was a bit annoying as I can have 2 120mm fans on the top, then the other had was used at bottom front panel. Luckily cables provided just about reached, they wouldn't without my additional fan controller. Just a FYI for all who do not place all fans together in a true daisy chain. Update: bought another set of 3 RGB white to complete the aesthetics. I was thinking adding the other 3 fans would be more audible but nope, exactly the same & still quiet enough. Pushes more air through and dropped ambient temps another degree and highest temps also by 2 degrees. The daisy chaining was still a pain in the rear. Luckily I've got a bunch of extender cables just incase & to help the addition of future fans to add later down the line. Overall, currently benching the machine. Cpu temps have dropped by about 10 degrees underload, idling at 32 degrees. Motherboard idles at 30 deg rather than 49. GPU dropped from 65-76 down to 57 deg C underload, idle dropped to from 40 down to 24 degrees w/ fans at low RPM on the gpu itself. Ambient case temperature has dropped from 68 down to 52 degrees. The machine is now cool inside at max load. Much happier, but the gripe remains about daisy chaining. Used SignalRGB to override all colours and working well.

I love It 😍❤️

Chegaram muito bem embalados os kits, prontos para por na máquina.