POWERTEC 71371 24 Inch Double-Cut Profile Universal T-Track with Predrilled Mounting Holes, 4 PK, T Track for Woodworking Jigs and Fixtures, Drill Press Table, Router Table, Workbench

Great quality, good value. There are a ton of cheap T-track and associated hardware out there, but you need to be very careful as tolerances and "standards" vary amongst manufacturers and not every piece of T-track will work with all T-bolts, etc. I have found POWERTEC T-Track and hardware to be very reliable, consistent, well made, and well packaged. It is my go-to brand for everything in this category (i use primarily for wood working jigs, drill press tables, router tables, etc.)

Great rail system for anything, I use mine for kayak's attachments and tool shop guides and more.

I installed all four of these on a crosscut sled and they're solid and well-built. I had no issues with the track size and all bolts slid in and out easily. I used epoxy to secure them, as the sled is not very deep, but there are pre-drilled holes. Track was easy to cut to size but clearly strong enough to take abuse. Great value and will definitely buy again for my next shop project.

T-tracks .. not much to say. They work. Kind of lightweight compared to the name brand ones. It would have been nice if they came with the right screws. I had a hard time digging up some that had a small enough countersunk head. If they protrude at all the track bolt gets hung up.

This is my second batch of T-Track from Powertec ... the first (in 2020) was four 36" tracks that I sank into my CNC router spoil board, and this four-pack of 24" tracks was used to make a crosscut sled for my table saw (pictured). Aside from having to provide my own #6 wood screws to secure them, I'm very pleased with the tracks.

Used for my table saw sled and fits like a glove.

Great for a starter workbench. For my needs they are awesome, makes clamping wood for various tasks on the workbench so much easier. I combined these with the POWERTEC 71168 5-1/2" L x 1-1/8" W Hold-Down Clamp, 2PK , POWERTEC 71121 16 Piece 5/16" T-Bolt Kit , POWERTEC 71068 T-Track Knobs with 1/4-20 by 1-1/2" Bolts and Washers(Set of 10) , I also added these, ( Hard-to-Find Fastener 014973243807 Full Thread Hex Tap Bolts, 1/4-20 x 1, Piece-100, Hillman 150003 Coarse Thread Hex Nuts, 1/4 X 20-Inch, 100-Pack, Stainless Steel Flat Washers 1/4" Screw Size,0.63" OD, 0.06" Thick (Pack of 100) ) and just filed the letters off the heads, they work great in the tracks, I got some extruded aluminum flat bars, 1/2 " by 1" x 12" from stoner metals on amazon, to use both on the tracks to hold wood while sanding, planing, and for use as spacers etc. The bolts are perfect for working with 3/4" stock, I just used a Dremel to trim the extra length down will attach some high density foam stripping to grip the wood. The kits work great, but the knobs are to high when planing. so the bolts are used when low profile is needed. Next will be adding rails to the long side of the workbench to use for a router sled. This t-track system will work well for holding pieces to route with the sled. First pic is holding down the saw guide over the bar in the second pic, which shows an 8ft bar with the bolts being used, makes a nice known straight edge that won't budge, makes squaring off 30 ish raw milled cedar boards easy. Yeah don't have a table saw, or room for one. So this works.

Great little T-slot rails! Not too expensive, but work great! I'm using these on a reloading bench for mounting presses and other tools. They make it easy to remove tools, or rearranging my setup. Quick tip! Get some 1/4-20 bolts and grind off opposing sides, allowing them to slip into the t-slot from the top and not the end. This makes installing and removing items much easier and faster.

Good value for money track, very pleased with my purchase.

I just installed the Powertec Universal track for my router. They are well made and good quality material. I got the 4 pack of 24" tracks I will possibly be needing more.

La extrusión de los perfiles de aluminio, de mucha calidad y precisión.

all good

Great t track for table saw ,router, drill press .Could use this track for many Woodworking applications .Will order again from this sellar