Hogue HandAll Beavertail Rubber Grip Sleeve for GLOCK 19, 23, 32, 38 (Gen 3-4)

This is one of the BEST upgrades for ANY GLOCK bar none...yeah, it's difficult to install but with patience and perseverance it can be accomplished. I would definitely suggest used a vise to hold the firearm, the Windex is a MUST to help slide the grip on. Using the plastic from the packaging as suggested definitely helps. The GRIP and FEEL of my firearm is 100% better....for the price it's the cheapest upgrade you'll ever do that results in better accuracy for sure.

These things fit like a glove in your hand. They do make the grip larger in circumference so if it's large already you might go with a talon rubberized grip as they don't increase the profile much. Follow the directions and use window cleaner as lube as you forcefully install the grip. It takes a lot of effort , but watch where it hangs up as you'll slide it over the grip and put pressure inside to push it up and over the edges.

The Hogue Handall Grip is hard to install but worth the effort. If you have extra large hands, this grip will make holding your Glock 19 more comfortable and more natural. Also, it makes the finger groves on my Glock 19 Gen 3 make sense. After getting my Glock 19 Gen 3, I understood why many reviewers had disparaged the finger grooves. Without the Hogue Handall Grip, the finger grooves felt vaguely helpful and mildly uncomfortable, but the grip enhances the grooves, helping me to get a more secure grip on the pistol. Yes, as other reviews mention, the grip is tough to get on, no matter the technique used. I tried all of them, from using hot water, using cut pieces of the plastic packaging, using a hair dryer, using 99-cent store Windex, and using a spoon. In the end, what worked for me was softening the grip in boiling water, placing the handle end of a spoon inside the groove side of the grip, and getting the back strap side on enough that I could use the spoon to stretch the groove end past the magwell opening, then spraying Faux Windex on the spoon and rubber grip which made it easier to slide the grip down the spoon handle past the finger groves, then spraying Faux Windex on the back strap side and sliding that side in place. I had previously tried all the other techniques while putting a Handall Grip on my Glock 26. After an hour of failure, I got the above process to work. My Glock 19 install took 15mins, including the 10mins to microwave the water.

I can confirm that this perfectly fits the Shadow Systems MR920 Elite with magwell and "high" backstrap attachments. My hands are a bit too big (long) for the gun as shipped, causing my accuracy to be all over the place. Putting this grip sleeve on it got me back to comparable accuracy with my larger-gripped Glock 17 Gen 3. The sleeve added noticeable thickness/circumference to the grip, which made a huge difference. Note that I had to remove the magwell attachment to get the sleeve on, and the instructions did not work for me with this gun. Don't bother with cutting out plastic "shoe horns" at all. Just thoroughly heat the grip in almost boiling water, spray Windex inside the sleeve and on the gun grip, and (contrary to the instructions) slip the sleeve over the front of the grip first, then force the sleeve up onto the back of the grip. It took me about 3-5 minutes to get it fully installed. I have an FDE gun, and the FDE grip seems to be a pretty much perfect color match. I think it looks really good once installed, and it feels great to hold the gun now (much better than before). It seems like it will be very durable over the long haul (just 50 rounds fired with it thus far), but only time will tell.

GREAT GRIP...CAN TELL THE DIFFERENCE AND HELPS KEEP THE FIREARM SECURE IN YOUR HAND WHILE FIRING...nice recoil absorption and get your sights back on target! ONE PIECE OF ADVICE ON INSTALLING....I BOILED WATER TO BETWEEN 80 TO 100 DEGREES POURED IT INTO A LARGE BEER MUG AND SOAKED THIS THING IN THE WATER FOR ABOUT 3 MINUTES...THEN TOOK IT OUT WITH A PAIR OF TONGS SPRAYED THE INSIDE WITH WINDEX AND SLID IT ON THE HANDLE...NOW IT'S TIGHT, SO ONCE YOU SLOWLY GET THE EDGES ALL AROUND THE BASE AND START NUDGING IT UPWARD, THE RUBBER SHOULD BE NICE AND WORKABLE TO WHERE YOU CAN SLIDE IT UP, ONE SIDE AFTER THE OTHER, UNTIL YOU GET IT IN PLACE, ROTATE IT A LITTLE (MAYBE) UNTIL IT'S JUST RIGHT. IF YOU SOAK IT ENOUGH YOU DON'T NEED PLIERS. I BOUGHT THREE OF THESE ONE FOR EACH PISTOL AND FOR THE FIRST ONE I USED PLIERS ON MY G27 WITHOUT WATER, WARMING, OR WINDEX AND THE PLIERS RIPPED THE RUBBER ALL UP...SO NOW I HAVE TO BUY ANOTHER ONE FOR MY G27 AND TRY AGAIN AFTER I STARTED TO GET THE HANG OF THIS AND GET MY RHYTHM GOING - FOR MY OTHER TWO (G23 AND G19) I WAS ABLE TO SLIDE ON FAIRLY EASILY ONCE I GOT THAT SYSTEM IN PLACE! READ THE REVIEWS OF THOSE WHO DID THIS BEFORE ME...TRUST ME, IT WORKS! GOOD LUCK! AGAIN GREAT GRIP!

Just arrived. Installed on G43x MOS sub compact. Took less than a minute to install it out of the package. Not sure why some people are having difficulties, boiling it in hot water and all this. Maybe you guys should put your purse down before trying 😉. I just placed it at an angle to get one side of the pistol grip in it, then wiggled it back n forth and slid it occasionally with hand around whole grip til it was complete. EZ PZ. That was 30 min ago so, haven't fired it yet but it is noticeably "grippier" and feels fuller in the hand with this installed. Pretty good.

Ugly but very functional. Locks you in great . Very grippy . Put on glock 19 gen 3 . I’m a fan of finger grooves and this makes them even better . Definitely a bulkier grip . Install was easy . Idk why everyone has such a hard time . Took me 5 min . I did not soak in hot water and I did not spray frame with windex . I was worried due to every video out there everyone struggling so bad to put it on . It was extremely easy just need to use common sense .

Fit my Glk 19 Gen 3 PERFECTLY and feels great!!! LOVE IT!!!

さわり心地がとてもよく、また太過ぎず手が小さくても持ちやすいので気に入りました。 裂けたとか書かれていますが、海外レビューに書かれている方法を実践したら普通に付きました。 まず2,3分湯煎し、そのあと説明書どおりパッケージをカットして靴べら的なものを作ります。(1個でいい) 作った靴べら的なものをグリップ前縁に当てて、内側にシリコンスプレーを吹いてからラバーグリップのビーバーテイル側を先に入れておき、靴べらを使ってラバーグリップの口をグリップに入れます。(このとき力が掛かるので、靴べら的なものの端が尖りすぎてると裂ける?) あとは熱いうちにグイグイ上に上げていけば普通に付きます。 英語レビューに失敗例も成功例も載っているので、届く前に読んでおくと良いと思います。

Fit my glock perfectly thanks

Nice grip