HUYUN 2 Sets Mouse Skatez & Mouse Feet & Mice Feet & mouseskates Replacement for Logit G502 Proteus Core / G502 Proteus Spectrum / G502 Hero Wired Mouse

Only replaced two skates that were damaged from an earlier operation. Months ago, I opened up a Logitech G203 mouse that stopped working and found that a cable had fallen out somehow. Plugged the cable inside back in firmly and it started working fine again, and continued to use it for many months, however, I damaged the front pair of feet which had to be removed to open the mouse. I put up with it until recently when the smooth coating wore away too badly, and ordered these. They came with a microfiber cleaning cloth, a sealed pair of alcohol wipes, a mini catalogue and the feet themselves. These are not the type that you place on top of existing, worn out mouse feet; they are full replacements. I removed the old, defective feet from the G203, cleaned the bottom with the wipe and cloth, carefully removed and applied the feet on the mouse, then removed the plastic film that protects the gliding mouse feet until use. Done. They look good, work quite well, and the mouse glides on the mouse pad like butter. Do you need precision tools for the install? I wouldn't say so, but it can be hard to keep an upside-down mouse from moving around while you try to carefully apply a tiny bit of plastic to it. Thankfully you get two sets of the things in case you mess up. Now, I didn't apply the pads on the other side nor on the center support, since those were worn, but still functional. Applying the ring-like center pad would probably be the most tricky, but if you're just looking to replace the oval pads on the four corner areas, these are simple to apply and a cheap way to refresh a G203 that is starting to have issues dragging on your mouse pad. Five stars.

Makes a huge difference on my old G502 Hero - also a great excuse for a deep cleaning... feels like brand new car! Or more like taking your old dirty car to the detailer and getting new tires. Fits perfectly. No cons, especially for the price. I used my own isopropyl alcohol to clean the old pad residue, not sure how far the included pads would go on that.

Nice product. Perfect fit for standard G502. I was testing the smoothness and noticed that the instructions reminded me to remove the plastic film after they were attached. When I did, they were REALLY smooth. BACK STORY: I had spilled coffee on my mouse and had to disassemble. I removed more of the skates than I needed to the first time. However, after I cleaned it and reassembled, one of the buttons acted weird. So that mouse had been apart a few times. The old skates were a mess. Now the mouse is working as it should, and has fresh new shoes for school.

Worked great other than they are apparently thicker than the OEM pads which creates tracking problems. This is not new, you'll notice people campaigning about the issue for reviews of most replacement pads. Had definite tracking issues after replacing the original feet/pads that I had to do to replace a switch. It was as I was lifting my mouse up, was constantly loosing tracking with my SteelSeries cloth pad. The solution was simple. Get a sheet of 220 grit sand paper, place it on a firm flat surface and rub your mouse over it to sand down about .5 mm. I just did it by looks, I sand a few passes then flip it over to see how far it has gone down. I actually used 120 grit since it's all I had on hand but it left scratch marks. It will work but 220 or higher is probably better. Then to finish it off, I blew the plastic dust off the back then took a sheet of normal notebook paper and rubbed the mouse (again feet down) for several seconds. This sort of buffed the sheen of the pads back out. Then finally take a lint-less cloth, or a tissue to make sure the sensor hole at the bottom is clear. No more tracking issues after doing this fix.

I've had my Logitech G502 for quite a few years, and have used it for many hours daily. I noticed over time it has become almost 'sticky' when making precise movements. and even after changing mousepads, and cleaning the bottom surface of the mouse, I could not get it to have the same level of precision it used to have. Enter the mouse skates! I highly recommend purchasing a pair of precision tweezers if you don't already have them as it makes removing your old skates, and peeling the covers off the new one way easier than picking at them with your fingers. Installation was quick and easy with the tweezers, and the new skates fit PERFECTLY. They look better than the factory ones in my opinion. I didn't take before and after shots, but if you have this mouse and you see the original skates look scratched, you're probably due for replacement. These things are BUTTERY SMOOTH. A night and day difference, and I didn't have to go out and spend $100 on a new mouse. It even comes with an extra set, so even when the pair you put on wears out, you'll still have another for only 7 bucks! I'll try and come back and comment on longevity when I replace the first set. But I'm absolutely floored by the fit and finish of the product at this price point!

My G502 Hero wired mouse had started snagging my mouse pad. Turns out one of the skates had started lifting in the corner, not sure how, but no matter how often I tried to push it back down it wouldn't stay down and would again start snagging. I decided to get new ones and these seemed like a good deal with good reviews. I got them quickly as expected with Prime shipping and went about putting them on. Taking the old ones (OEM) off didn't seem like a difficult task, but when I went to use the alcohol swab to remove the residual glue I realized my OEM pads had actually come off in half. I had to spend a little bit of time scraping the rest of the pad off the bottom of the mouse but eventually it all came off and I was able to clean the plastic with the included alcohol swabs. After I had gotten all the old pads off, the new ones were fairly simple to put on as long as you aligned them correctly. One was a little triangle and I took some time to figure out the correct orientation, but once I was able to put them all down and press a little bit on them they all stuck very well. There is a bit of film on the sliding side that you have to get off. I did it after sticking them on and didn't have any problems. Now my mouse slides great and no longer snags the mouse pad. If in the future it does start to snag again or something I do now also have a second set to replace with again. I can't remember if it was these or another set but a commenter complained about the color not being a match with the mouse. Mine seems to be fine (see picture)

Wow. So I almost left a bad review. I removed the stock skates from my G703, cleaned the feet, and then applied these. I was super bummed. They felt worse than the stock ones. They felt almost grippy to my mousepad. I played about 4 hours of The Division 2, then when I logged off I went online to check if these were counterfeit using the scratch off code on the back of the package, which lead me to a thread where one user was having the same issue as me, and somebody asked him to "remove the clear plastic from the skates". I'm an idiot. You don't have to be an idiot too. After you apply the skates to your mouse, there's a thin plastic layer that covers them, similar to how electronics etc have that peel off layer of plastic. After I removed them GOOD GOD these things are slick! Literally feels like my mouse is hovering on a layer of air. It's super impressive, and I'm super happy with the skates.

Works perfectly for an old mouse that otherwise is not malfunctioning. The pads are cut accurately and stay attached with no issue, thye present a great value. It is very important to ensure you remove ALL the old adhesive before applying the new feet as this will prevent them from sticking. Also remember that the feet have a layer of plastic on the surface meant to contact the mousepad, Remember to remove this plastic as it's not meant to stay.

Son esactamente las de Logitech G 502 hero.

Not a 100% match to the G900, OEM ones fill out the place completely, these have tiny gaps but after years of worn pads, the difference is noticeable and has brought my G900 back to new.

These are not as thick as the original Logitech G703 feet. They BARELY clear the plastic part of the mouse by a small fraction of a millimeter. I've taken a picture to show. Also the edges are very sharp and scrape the cloth mousepad. It literally sounds like sandpaper to use!

غيرت الزلاجات اليوم بعد ماكرفت الماوس حقتي سنتين لكن انصدمت من النتيجه ابدًا ماحبيتها فيه خشونه وتثقل اللفه شوي

تم أرجاع المنتج لأنه غير مطابق بعد أنتظار فترة طويله جدااا