Mytee ProductsHeavy Duty Adjustable Trailer Stake Pocket D Ring w/ 1/2" Hitch Pin, WLL5400 lbs & 4 Holes for Adjustment | Stake Pocket D-Ring Tie Downs Utility for Flatbed Trucks and Trailer – 8 Pack

I can't tell you how much time i spent measuring the stake pockets on my aluminum trailer and researching for stake pocket D rings that would fit properly. The dimensions "CLAIMED" on these would be great. I get them in and the dimensions are WAY off. They are quite a bit smaller than advertised. VERY disappointed. These are NOT the claimed 3 1/2" x 1 1/2", they are 3 3/8" x 1 3/8" I'll be returning them and take my money to a manufacturer that can measure properly.

I have a 2018 Carry-On flat-bed car hauler trailer. These D-rings fit the pockets perfectly.The Mytee Products D-rings are very heavy duty. These have a WLL of 5400 lbs and are marked as such. The D-ring is much bigger and heavier than I expected. The workmanship is very good on these and the welds look great.They include the pins/cotter pins to secure these to a trailer stake pocket but I'm going to weld them in place because I can't ever envision needing to remove them. It'll also keep them from growing legs and walking away! Welding also solves the problem of the D-rings being too long for my short stake pockets. No movement with them welded.Very happy with this purchase.

I don’t typically take the time to write reviews but feel I had to in this case. Firstly, as others point out, this is not zinc coated, but painted silver, perhaps with zinc content.More importantly, one of the time downs received has a very porous weld almost as if it were MIG welded without gas shielding. See in the attached pictures. This is a safety hazard and should not be used to secure any cargo. I would like a response from either the seller or Amazon regarding this unsafe product.

I see complaints about packing, well the seller listened. I ordered 8 of these. There was 4 only per small box, each piece was wrapped in a sheet of foam, along with packets to absorbed moisture. The two small boxes were in a large box that was double wall thick cardboard. That box was in another box from Amazon. Zero damage or even scratches on them. I have a 5 ton trailer with very large D-rings welded to it, these are the exact same size. They fit easily in my post slots inside the rub rail. These will eliminate any chance of an error I see a lot of private guys do, I won't have any straps or chains wrapped around the outside of the rub rail, which is illegal to do in NY. These are great. Very well made, very strong, they are not intended for a light weight trailer. Measurements are given in the add and are correct. Be sure to measure your post slots, but it a 2X4 fits in it, these will fit. I put a 2X4 in my slot, it fit very tight. These fit with a little bit of play. IM VERY HAPPY WITH THESE, THANK YOU.

This item fits the pocket perfectly. It is very heavy duty. The d-ring is what I've been looking for.The problem I have is with the hitch pin. The hole for the cotter pin needs to be drilled about an eighth of an inch further out. Presently it's to snug against the side of the pocket. The lip of the pocket interferes with the cotter pin going in but I was able to get three of the four in place. The 4th I'm going to have to bend the hitch pin just a little bit to get it to slide far enough in to be able to get the cotter pin in place.

I use haul ton of large farm equipment, IBC totes full of water, firewood, off road vehicles, hay, etc. As you know, if you are considering this item, using the pockets on the trailer can be a pain. Too narrow for the chain binders or some ratchet strap hooks, thin and can bend if you place the chain hook directly on them. They just aren’t ideal for hauling. These solve that issue 100%. They fit perfectly in a standard sized pocket. If you are unsure, use a 2x4 to check your trailers pocket dimensions. If a 2x4 fits, you are good to go. Hauling has never been easier. Only one cautionary note... of left on the trailer when not in use the vibration of the road will cause the rings to rub your trailer and may remove the paint. This happened to me. I have a hand painted Diamond C 10 ton and these took the paint right off. My bad.

I bought 8 of these to hold quads on my trailer. They work well for my application. Some of these are a little off...so the pin can be difficult to get in. Nothing so serious that I wouldn't recommend them. If necessary, I'm sure a little whack with a small sledge would make it all easier. That's what happens when you go heavy duty sometimes. The price is well worth it. They're holding up well. No quads flying off my trailer!

Good value for some fairly heavy duty tie down points. It doesn’t seem like zinc plating (not sure), but more like silver paint. Holes for the pins vary in size and some would not allow the rod to go through all the way to fit safety pin. D-rings are very stout, but the “channel” style metal bases are actually (formed with a break) thin steel plate material. Not too thin, but I expected slightly thicker guage steel.

Very strong and well made. I had to notch out the bottom of my stake pockets for them to lock, but that is a trailer issue.

Exactly as I wanted .Arrived in reasonable time