Sony AGR2 Attachment Grip (Black)

I recently purchased the Sony AGR2 Attachment Grip for my Sony camera, and it has significantly improved my shooting experience. The grip is comfortable and adds a lot of stability, especially during handheld shots or longer shooting sessions.The build quality is solid, and the grip feels secure and ergonomic in hand, allowing for better control and reducing hand fatigue. It’s also lightweight, so it doesn’t add unnecessary bulk to my camera setup.Attaching the grip to my camera was quick and easy, and it fits perfectly, providing a snug fit that doesn’t interfere with any of the camera’s functions. I noticed a big difference in my ability to hold the camera steady, especially when shooting in low light or with longer lenses.Overall, the Sony AGR2 Attachment Grip is a simple but highly effective accessory that I’d recommend to any Sony camera user looking for better handling and comfort.Pros:Comfortable and ergonomic designEasy to attach and secureImproves stability and controlLightweight and doesn’t add bulkCons:None so far

A common comment, if not complaint, about Sony’s CyberShot RX100 series of digital cameras is that the cameras are so small, and their surface finish so slippery, that it’s difficult to hold onto them when you’re trying to take pix or videos. I find that comment completely accurate; I always felt that I was on the verge of dropping my RX100M7 every time I fired it up, even though I had the wrist strap wrapped around my hand.That is, until I installed this Sony AGR2 Attachment Grip.This minuscule piece of black plastic improved the whole character of the camera in meaningful ways. Its slight bulge at the front of the camera, and its textured matte-finish surface, combine to provide both a little more bulk to grab onto and a little less slippery area to do so. Together, the result is much more secure handling.Installation is simple and straightforward, and the grip fits the camera perfectly. The adhesive sticks well, and I scrupulously followed the instructions, which caution: “Adhesion is not stable for several hours after attaching the attachment grip. Start using the camera again about one day after attaching the attachment grip.” By not using the camera for more than a full day after I installed the grip, I assured that it’s as secure as it will ever be; it feels like it’s molded right onto the camera (I didn’t try to pry it off, of course!). The adhesive will likely eventually dry out in the arid desert environment where I live. If it does, and if the grip falls off some day, I hope it doesn’t leave any residue on the camera that would make it difficult to install another one.Other reviewers complain that the camera with grip doesn’t fit into certain cases, and I’m sure that’s true. But the WERJIA Hard Carrying Case (ASIN B094N6GXCV) that I purchased holds the camera with grip with no problems at all.Whether or not Sony should have included this grip in the box with their pricey camera can be debated, but, since they didn’t, this add-on makes a great camera even better. Sure, it’s a lot to pay for a tiny piece of molded plastic, but the resulting improvement in the camera’s grippability and handling is well worth the price. I enthusiastically rate it at five well-deserved stars.

Bought this for a RX100 III because the stock design is a bit too minimalist and not functional enough. This adds a small rubbery grip to the right side of the camera where it is normally very slick and metallic.It feels like a good quality product and fits perfectly against the curves of the camera. It looks very natural like it was built on the camera and for me it adds to the design. The installation was as simple as removing a wax back from the adhesive and applying the sticker to the camera. I didn't do anything fancy, I just lined it up and plopped it on. It seems to hold pretty well although if you apply it fairly lightly at first you do have the ability to adjust it perfectly into place before really sticking it to the camera.I think it is a great addition to the functionality of the camera without adding a lot of bulk like a case would. For the $15 I paid I think it was a decent price for what it is and the quality but I had to reduce the review by one star because for the price of these cameras and the price to make these grips, I think it should have been an included accessory. I know a lot of people might not use it but I think a lot of people would and it wouldn't have had to become an accessory for profit considering how slippery the camera feels in the hand. People may not feel this was enough justification to reduce a star but I think it is.Although I think it should have been included, I definitely recommend this at it provides much needed grip for this camera without adding bulk. The price could have been better but I have seen other more fancy and custom options for twice as much.