Dorman926-446 Front Driver Side B Pillar Molding for Select Chrysler/Dodge Models, Black

I wrote this as an answer to the question if the screw was included, but feel it should be posted here also:No screw, no instructions. Pretty self-explanatory just looking at it, though. You'll need a second person to push in and push down, top and center. You can look through the side to see how much further you need to go by looking at the peg for the screw hole. Don't press in at the bottom till the screw peg lines up with the hole. Most important part of the whole operation is to leave the adhesive covering ON and sticking out the side and top of the applique. Mine was a blue plastic. Slowly peel it off once everything is in place.

I bought this part to replace one that came loose while driving down the expressway and eventually flew off. If I would have known that the dealer was going to charge $93 to replace it, I would have pulled over and tried to retrieve it. After finding out the dealer's price, I decided to find the part on my own. Luckily I found this one on Amazon for less than half the price. This part is for the driver's side front door. There is one screw on the inside of the door that the part attaches to. It also attaches with 2 strips of adhesive.To install the piece, here is what you should do. DO NOT REMOVE THE ADHESIVE COVERS YET! I figured out this is the best way to do it. I did it differently and exposed the adhesive first and this made it very difficult. I ended up reapplying the adhesive cover strips to do it right. First, there are 2 square padding stickers around 2 brackets that will need to slide into place on the vehicle. I found that removing these padded stickers was the easiest way to get the brackets to fit into the "holes" (not sure how to describe this part) on the car. You'll have to carefully bend the panel to side both of the brackets into their places. Then make sure the screw hole lines up with the screw peg on the panel and screw in the screw (it's a star head, not philips). Once you get the panel into place, you can pull the adhesive cover strips off. There is extra length of cover strip that should stick out of the top that you can pull. Now push on the panel for a bit to get the adhesive to stick.

Once I learn how the original was attached it explained a lot.The old adhesive was a booger to remove. Hope this one holds as good. Installation was a little tough. Really need two people, one to press down on the appliqué where it attaches to the door while the other pulls down on the end where the screw attaches. Only thing I would suggest: Would have been nice if some instructions were included in the package.

Installation is straightforward, just remember to NOT remove the adhesive protector until you are sure the clips are slid in correctly and you’ve screwed in the one screw that holds the part to the door. The product appears to be a different shade of black than the OEM part, but I’m not sure if that’s due to the age of my vehicle. Still, for the money, it’s better than having to pay full price for the OEM.

Perfect fit, the item feels and look like the original part. be aware I can see the difference with the new and the old trim, but is becasuse is new!! and the rest of the trim is old. Insatalation was easy, just do not peel the tape tabs before is install, then just peel the plastic tabs off then puh plush to the car.I would buy this item again. Thank You

I got this one after the factory one flew off one night. It took a little bit of effort, to get it in the right place, but it fit perfectly. Hint: don't remove the liner for the adhesive strips until everything is in place.

Someone ripped the old one off my wife's car in a parking lot so I had to replace. This one fit perfectly. Got here in a day and install was 30 seconds. Cheapest I could find 10 out of 10

It was easy to install but had to buy additional adhesive used for cars for good measure and attached it

there is a foam tape surrounding the clips that make it hard to instal, since they are poorly placed and interfere with the clips. the clips are very thin and very easy to break when installing so be very careful as it is difficult to align both. Many people have complained about the thickness, chances are they didn't have the middle clip inserted correctly. since mine broke and the van is old, I cut out the middle clip and used some PL Glue. Seems to work, just not happy that I had to modify a new part to get it to work.

Installation plutôt facile... montant de gauche sur la photo très similaire à celui de droite.

Fits my Dodge Caravan perfectly. Watched a youtube video on how to install it. It was easy and looks original. Shipped within a couple of days.

good fit but was very difficult to get it to slide into place when the tape protection was removed

Perfect fit…can’t tell it from the original