Highwild Adjustable Target Stand Base for Paper Shooting Targets Cardboard - USPSA/IPSC - IDPA Practice

I used five 8' 1"x2" (.75" x 1.5") inexpensive furring strips. Two 4' uprights, four 2' legs, one 4' cross piece for each stand. I like the adjust ability of the brackets and the convenient knob-ed fastening screws . The assembled stand are lightweight, disassemble for easy storage and transport, and very stable. The leg brackets are angled downward to compensate for uneven ground. I used 1/4" x 1.5" carriage bolts and wing nuts instead of the provided hex head screws for securing the legs. I also marked the cross piece to quickly identify the spacing for various cardboard backer widths. The eight supplied clips for the cardboard backer is a thoughtful convenience, as are the four 11" ground stakes. I keep the brackets on the cross piece and Velcro strap the uprights and legs to the cross piece for easy storage and transport. I highly recommend this well designed target stand.

I picked up three of these originally for doing drills and taking friends and family to the range. I stopped by Home Depot to pick up a bundle of 1"x2"x8' set the targets up at home. The build quality is very consistent and they hold up well to wind. Picking up a few more because its easy to stack these deep in my truck bed, but I would pick up some extra alligator clips because you go through them faster then you would think. The cardboard backings are reuseable and I staple new paper targets to them to extend the life of them. Pickup a rubber mallet for the stakes.

Great, simple stand that is easily disassembled/assembled for easy transport. Would give the fifth star if it had thumb screws on the leg sockets as well. It comes with screws, but I just slide the legs in without using the retention screws. Would probably use them if they were mounted thumb screws. But, I realize that would bump the cost up a bit more. I did cut my legs a bit longer than suggested to add stability. It isn't "heavy duty," but it's light weight makes it perfect for portability.

This target stand is the item I been looking for. It is so simple and portable. I assembled it quickly and it is sturdy. I did not use the screws that came with it. I wanted to break it down easily and I wanted all the pieces to remain with each other for ease of transport and storage. I went to the hardware store and purchased 1x2 furring strips: (2) 6 foot, (2) four foot. I purchased 4 pins, 1/4” in diameter, 2 inches in length. I cut one 4 foot 1x2 furring strip into 4 pieces for the legs. I fit those pieces in the base and drill 1/4 holes in to the wood. I then inserted the 1/4 “ pins into the holes to hold them into the base. They where a bit tight, but the held them in place nicely. Next I took the other 4’ 1x2 furring strip and inserted then into the base. I did not cut this strip, I wanted to be able to adjust the width, based on the targets I use. The metal strips that are included, I had to bend them so the line up with the holes for the knob studs. Once I installed the knobs, I slid the 1x2 into the base. I had to push up on the metal tab so the furring strip could slide in. Once I done both sides. I left them on. I installed the metal strips for the upright supports and did the same thing to get the knob stud to line up. I need to purchase 2 Velcro strips to secure the up right strips and the “ legs”. See attached pictures. I scribbled numbers in the base strip, not the best. I probably will use a label maker.

This target stand solves a big problem. It gives me the freedom to set the target at any distance I want, not just the standard distances so familiar at the range. I can take it down or put up easily and in a short time. Best of all, I can put it where I want to put, not just at fixed standard distances. It is a great addition to my gear.

This little target unit was exactly how I pictured the perfect stand in my mind! Ordering the unit was easy and the delivery time was outstanding. When I went out target practicing, the stand exceeded my expectations. The stand is extremely sturdy and very well made. It was easy to break down for transport and storage. I may purchase a couple more sets to get a “complete firing line”, so my buddies can enjoy the experience as well!

This product has one of the most blatant omissions I've ever seen. This product requires wood cut to size, and is needed on the legs, between the two braces and for attaching the target. WOOD DOES NOT COME WITH THE PRODUCT. You now have to go hunting for the proper size wood. Yes, the stands look easy to assemble......AFTER you go hunting for the proper size wood (1x2) AND cut it to size. THEN you can put the product together.Once it's all together, this might turn out to be a really good product. You just can't just open the box and put the thing together as the company implies. No matter how good this product turns out to be, I doubt I'll change my review score to a better one because of this glaring omission.

I had built a plastic pipe stand and it was pretty good but it big and bulky and ugly, a pain to get to and from the range. Why build you own when for about $5 to $10 more you can have a sturdy well built thing of beauty that works extremely well and is easily transported to the range for quick assembly. This really is a great product. I used the same furring 1 x2’s that I had purchased for my plastic pipe stand. This really is a great product. Buy it