JumblSINSB7W ProGrip Ultra Stainless Steel Speaker Wall Mount Bracket White, Pair of 2 - Thread Size: 1/4-20 - Holds up to 10 Lbs

Needed some mount for my new outdoor speakers and was looking for something flexible and cheap. These work great and hold my kicker speakers no problem. There 6 lbs so not very heavy and these mounts could hd something twice as heavy. Very flexible and can tilt and turn the speakers a fair amount before the speaker hits the wall. If using with smaller speaker you could do 180 degrees no problem. Super easy to install and adjust with an Allen wrench.Only negative is they don't come with hardware to mount to the wall. I understand this as there so many different pieces of hardware they would have to provide to install into all the different types of walls. I used some structural wood screws to mount them through my aluminum siding into the studs. Worked great

I was a little nervous about getting these due to some reviews mentioning items arriving damaged, as well as some complaints about installation. I had zero issues installing these. I mounted my vintage NHT Super Zero XU speakers (5.2 pounds each) with these. These speakers have the rear threaded mounting hole (as opposed to a keystone hole), so I easily threaded the ball onto each one (with thread lock) and then tightened the nut.I had no issues tightening the clamp, loosening it enough for repositioning the speaker, then performing a final tightening. The mounts are very secure and have almost no sag with these speakers. I suspect that these would work with a 10 pound speaker, but you probably would experience some noticeable sag. However, you could probably compensate by aiming the speaker a little higher before your final tightening of the clamp.Note - these mounts do not come with screws for mounting them to the wall. You will need two appropriately sized fasteners of the appropriate type for your wall to attach each mount to the wall.

Worked very well. Durable, easy to install. Great price and size.

I don't know what all the negative feedback on these was all about, because I had absolutely no problem at all with them. Excellent quality, well made and a great design. Just don't try to hang a speaker that is too heavy on them.

These work great. Would happy purchase again if I needed more. No complaints.

Works great for speakers that have a threaded insert (1/4”-20 thread) in the rear of the speaker cabinet. If your speaker doesn’t have a hole in the back that is threaded for a bolt, then these mounts won’t work.Also, the mounts do NOT come with screws or hardware that attach it to your wall. I’m ok with that. There are multiple materials (drywall, studs, plaster, brick, cement, etc.) you can mount these to, and each requires a different fastener. I attached mine through drywall into wall studs, so I attached mine with #10 x 2” wood screws. I drilled pilot holes first with a 1/8” drill bit. If you mount to drywall, then I recommend drywall anchors with #8 x 1-1/4” screws. At any rate, get the right fasteners for your wall. Each mount has 2 holes.The seller should say this in the listing. It’s confusing because the listing says “ The mount comes with all the mounting hardware you need” which is just inviting confusion and resentment when you open the box and find no mounting hardware. Should also say “your speaker must have a threaded mounting hole”.

These would have been a five out of five but much like other reviews, while these wall mount brackets are great, after two shipments and having all four come in scratched, I finally just kept the best looking two and returned the other two. It's quite apparent that these could use a little bit more packing material to keep the studs from scratching the nice powder coat on the bracket

Used both to hold a Polk Monitor XT35 Center Channel speaker weighing 14lbs. It needed to be above the tv and angled down. Screwed a white melamine MDF board to the wall's studs and then drill holes in it to use 1/4-20 Hex Drive Wood inserts to attach these mounts to the board. I used the same inserts on the speaker since it only had keyhole holders. You have to be very accurate taking measurements and leveling. Bottom line, I was able to angle the speaker to my desire and the brackets handle the weight perfectly. A reviewer said that one of these wasn't holding his bookshelf speaker that weighs 10 lbs, most likely because it has too much leverage, the speaker is too deep and these were not designed for a speaker that big, regardless of its weight. My speaker is heavy but it is slim and not too deep, plus I am using both brackets; obviously I can only move the speaker in one axis, but that is all I needed. Also, the hex wrench provided is not convenient, it'll do the job, but it'll frustrate you. I used a hex bit socket and a ratchet wrench, so I could quickly tighten each screw while holding the speaker in the desired position.