Westinghouse 7224800 100-Inch Industrial Ceiling Fan, HVLS Indoor/Outdoor Large Commercial Ceiling Fan with Remote, High Airflow DC Motor, Black Finish

Edit: six-month update--still love this thing. Still absolutely silent; working without issue. Never cease to be amazed at how much air it moves--stirs up dog hair we didn't even know was there. Remote still feels astonishingly cheap. Still haven not gotten around to ripping the codes to use with Home Assistant. I'm a slacker, I guess. The original review follows: So I wanted to hook up a ten-foot (10') downrod to this thing, 'cause I've got a two-story, vaulted ceiling I'm working with. I did it and it works just fine--and it didn't even cost me that much. I bought a ten-foot 3/4" galvanized steel "structural pipe" from Lowe's. Cost me like $25. I am 99% certain it's made from the same factory that makes downrods. Looks identical. Same beveled edges and everything (it's not threaded). I had to drill a 1/4" hole through it in both sides, for the retaining pins. The center of the hole is 1/2" from the end of the pipe (the one closer to the fan is *maybe* a hair closer--pay attention to this, 'cause you've got less room to work with here--the top one, connected to the ball/bracket, won't really matter if it's off a little). I then had to extend the wiring. The inverter is up in the canopy, so it's not just a matter of extending the AC wiring--you gotta cut into their custom wiring for the DC & control stuff. Wheeeeee always fun to cut the wires on the $600 fan you just bought. I'm sure this will void the warranty. You're probably voiding the warranty just reading about it. Don't try this at home. Only a madman would do this. Anyway, I cut the wires, then spliced and soldered some 10' extensions. There are five wires. Three are 18 gauge, two are 22 gauge. I bought some wire from Amazon, was around $25. I already had some heat-shrink, but would've just covered it with electrical tape if I hadn't. Remember to slip the heat shrink on *before* you solder the wires! Just to be on the safe side, I also extended the steel safety cable. I bought some steel rope (thought it was the same size, but I think it was actually a size smaller than what's already on the fan) and some loops, aluminum crimps, and crimping pliers. I'm confident the cable would support my weight if I hung from it, so I figure the fan is fine. I was nervous when I got it hung and wired. It was a huge pain in the butt. Very heavy. I'm lucky I had some scaffolds to work on and a forgiving and very helpful partner. The blades are relatively easy to install. The instruction manual doesn't tell you this, but the bolts and nuts are all 10mm. The manual also doesn't tell you where the flat washers go. It also doesn't tell you how many of each part you have, the little crescent gaskets it shows are *not* included, and it doesn't tell you wrench sizes for anything. You'll notice that in the questions for this product, someone asked where the flat washers go, and the seller was all like, "iT's iN tHe mAnUaL" Yeah, it's not. I've included a pic of the only page showing the blade installation here, along with the bolts and washers you're given, and obviously, the manual doesn't show you anything of the sort. The bracket that the blades attach to is steel, so I figured the split washer would be okay against it, and used the flat washers underneath the blade, between the blade and the nut. It seems to have worked fine and feels pretty secure. I secured mine using a 10mm wrench on top and a 10mm ratchet socket on the bottom. When you're putting the blades on, start with the single bolt furthest from the center of the fan. Drop the bolt in from the top, press the blade up against the bracket, then place the flat washer and nut and hand-tighten them. This gives some "leverage" to the blade, so you don't have to keep holding it, and the other two can be relatively easily placed, then you can tighten all of 'em with a wrench & ratchet or whatever. I did opposite blades each time, so the thing didn't get too off-kilter or something. I also tested it after installing the first two, in case I had borked the wiring somehow. Thankfully, it worked great. This thing is really quiet. Amazingly so. I like it. The remote feels like a cheap piece of garbage you'd get from the Dollar Tree or something. I plan to yoink the rf codes and set up an rf repeater with Home Assistant, so I can tell Alexa to turn the fan on. My wife will think that's cool. Anyway, it works well. It was expensive, but feels pretty decent. I'm happy with the ten-foot downrod (it's a slightly different color of metal than brushed nickel--sorta blue-ish--but it doesn't bug me too much) (note--Lowe's also sells this stuff in black, if you wanted to get the black version of this fan--not sure if the blacks would match, but it's black, so unless you're Tom Haverford, you probably won't notice (if you get that reference, I love you)). It moves a LOT of air--I could feel it even on the lowest setting. You'll see the paper lanterns in the pic (hey, sue me--they were cheap--have you priced lighting lately?); they get blown around a little, which is mildly annoying. Even on its highest setting, I can't hear it, but it's moving air like crazy. Pretty awesome. Good stuff.

OK, shopped around for large workshop fan and this one looked good at decent price point. I purchase one just to see how i liked it, it worked so well I purchased 2 more within a week. My shop is 40’ x 60’ x 16’ ceiling and the 3 fans do an excellent job at air movement in Florida heat. A few questions that I had but couldn’t find an answer prior to ordering. 1. The fans do have a memory, meaning you do not need to use the remote to start it. Set what speed / direction you want and the fan will turn on to those settings when power is applied. I hate remote fans big PITA! 2. The remotes have no “dip switches”, meaning the remote is “hard coded” to that specific fan. So if I wanted to use the remotes I would need to use all three individually. Again big PITA, but no problem with the unit memory. 3. The fan has a large mounting bracket that does no bolt up to a normal 4” round ceiling electrical box. The bracket is about 6” wide and bolts up to the ceiling directly. It comes with 4 concrete expansion anchors. I bolted mine directly to my 2x2 steel trusses. 4. The speed controller has two heavy plastic rings around the wiring harness. They don’t tell you what they’re for and take up a lot of room in the tight top mount. They “could be” just packing or they could be CTs (current transformers) that provide feedback to the speed controller. Not sure so I left them in and worked with the tight space. Good hunting and see ya!

Looks great and moves air but to turn it on, you have to flip your wall switch AND THEN ALSO use the janky cheapo remote to hit the on button as well. There is no way to turn it on if you don't have the remote! So what happens when you lose or break the remote (which by the way looks like the cheapest of cheap China-made junk)?! Why would you not have a memory function that allows the fan to just come onto the last setting when it's turned on at the switch?!? What a ridiculous shortcut. Do not buy unless you want to put your entire $600 investment into the hands of a cheap janky remote.

I had a 96" Minka Aire fan that was solid for about 2.5 years. Had it in our Great Room hanging from the truss and it seemed to do everything we needed it to do and it looked great. It developed a problem overnight that made it sound like it was going to come off the down rod. An annoying grinding sound like some fasteners had worked loose and rubbing on the metal housing. A thorough inspection showed no sign of looseness or fasteners out of place. Many hours on the phone with Minka trying to resolve. They were adamant about the electronic controller was to blame. I replaced 3 times and reprogrammed the fan...no luck. I really wanted to resurrect the thing but it was not to be. It lay dormant for about 8 months considering I hate heights and dangling from a ladder 24' in the air makes it difficult to do much of anything. I searched for months for an appropriate replacement. I read all of the reviews on anything that came close to what we were looking for. There always seemed to be some technical anomaly that would show up or the observation that the fan just didn't move enough air for its size. Then I came across this Westinghouse Industrial fan (7224900). It was sleek, it was the right color for me and it had a blade span of 100". I tried to find some kind of exception from reviewers, but the only complaint I could find was related to the lightweight cheap feeling remote control and the fact that you can't control from a wall switch. I didn't care about that so much as I did about the performance of the fan. I bought it, installed it and it is awesome. Even on its lowest setting, this thing moves air. Its like an ocean breeze pouring over you in a subtle yet effective way...not like a wind tunnel mind you...just very soothing. Our great room is about 22' x 28' with a pitched ceiling height of about 30'. I haven't found anything negative about this fan. I believe the rigid aluminum blades make a huge difference in the way its able to move the air unlike most other large format fans with floppy blades and the pitch seems to be ideal. Worked for me!

Truly excellent indoor/outdoor fan for ceiling mount within protected spaces. I installed mine in my 24 x 36-ft. pavilion and it moves a ton of air without any appreciable noise. We liked this 100-inch fan so much that I've purchased two more. We're gonna have the coolest pavilion around! Remote control works flawlessly.

Ordered in Jan of '23 for my shop build. life happened and the build took longer than expected. Fan sat in the box, on a shelf since delivery. Electricians opened yesterday (6/22/2023) to find the control module cracked and the fan does not work. Update: review changed to 4 stars. After much waiting and back & forth with westinghouse, i got replacement part in the mail free of charge. The only reason this review is not 5 stars is because it took 3 weeks to get the desired result and 9 days for anyone to get back to me after leaving messages initially. Great fan! Moves some serious air!

I researched all of the large industrial-style fans available and this one provides the best bang for the buck. We previously purchased the $299 70" Slinger fan which provides good airflow and style, but moved to a house with a larger 18' ceiling living room. So, I looked at all the large, industrial-style fans under $700 or so. The biggest complaint you'll see, as with the Hubbell 96" is people say that they cannot feel the breeze. We live in the south, so having a fan you can feel during the summer is important to save on cooling costs. I saw the same complaint about many other large fans in the $400-$500 price range, including the 120" one found at the orange retailer. Airflow: This fan is exceptional at airflow. If you check the specs, it reaches nearly 20k cfm, which is only half as much as $3k industrial fans. Most of the large (8' or so) fans like this are more in the 12k-14k range. This fan, even on the lowest setting moves ALL the air in our large living room. Turn it up on high and you'll have a breeze even in connecting rooms. I wouldn't mind to have a broader speed range, still topping out at the same place. So, make the 1st speed slower and spread the other speeds out. I have found that in the reverse direction, even on the lowest speed, it can move a little more air than you'd want when it is cold outside. The video I included is of the fan on the lowest speed for reference. Remote: The remote feels like they really didn't pay much attention. It feels cheap, looks cheap, and you have to flip a little dip switch to change the direction in the battery compartment. The fan also has a large beep noise on any speed change Quality: The fan feels a little rough around the edges, but kind of fits with the style of it. When the fan is off and you turn it on, there is this delay, then it ramps up quickly to the highest speed (it seems), then settles down to your setting. It is a bit startling to see this massive fan spin up like that, but it works. I also have a slight noise at times when starting the fan up, especially when switching directions, that sounds like a wire brushing against the inside of the housing. However, I don't want to have to exchange this thing, since it was such a pain to install. I have a very tiny wobble at level 4 and a small one at level 5 and 6. I was hoping for no wobble since it suggests this shouldn't be a problem in the manual, but I have no easy way to try to eliminate this. Install: So, you want this huge fan, which means you probably have high ceilings. Installing a ceiling fan like this is quite difficult on high ceilings because tall extension ladders need something to lean against, and most people don't have A-frame ladders that can reach 18' in the air. Be prepared to pay an electrician multiple times what a normal ceiling fan would cost to install, or be willing to build scaffolding. What I ended up doing was building a 6'x6'x10' platform in the middle of the room, then used a small step stool to reach the ceiling. The 10' platform reduced the distance to the ceiling for me to 8', which is easy to reach. It felt safe and steady to me, but I wouldn't want OSHA to inspect it. Don't have a finished picture of it, but added a picture where my tower was partially built. I had some plywood already, so the tower cost me about $80 in total to build. Install (fasteners): For some reason the box comes with expansion anchors that you'd typically use for concrete, which I found to be unsafe. It didn't discuss in the manual which types of materials they are suitable for. I'd worry that people would use these anchors on drywall or in wood. Instead, I added 2x8 blocking on either side of the joist that the junction box in the attic was connected to. I then purchased lag screws to connect into that blocking after pre-drilling the holes for them. This is very secure and will hold much better compared to the expansion bolts provided. While there are some rough edges, I highly recommend this fan to those looking for a large fan that can actually move enough air for you to feel it.

I looked far and wide for the right fans for our space. I bought and installed 4 of these. These are used in the 2000 sq foot “play area” of our real estate office, which we refer to as, The Idea Factory. We use the area for meeting with clients, hosting events, and renting out for parties, dinners, etc. We needed quality and effectiveness. These fans did the job. The wingspan is impressive, and the air output is incredible. (We usually use the fans on level 1 of 6. A few times we have bumped it up to level 2.) Our ceilings are 14 feet high and the down rods and housing put the blades at 11 feet high from the floor. They look great, and new visitors to the building always comment about how awesome they look against the black tin ceiling. They help our utility bill as we only have to use the air conditioning system on the hottest of days in that area of the building. (In the winter, we reverse the blades to assist with pushing the heat down from the ceiling area. I hired electricians to install them since we are on court square across from the building department! I didn’t want to get harassed during my final inspection. The biggest drawback is the touchiness of the remote controls. They are a bit cantankerous and sometimes require a few “clicks” of the buttons before the blades engage. I would definitely recommend these fans and wish you well on your project!