Keyless2Go Replacement for Keyless Remote Head Key Fob 4 Button KOBDT04A and OHT692427AA (2 Pack)

Instructions worked perfectly. Programmed within minutes.A: How to Program your Keyless2Go Key Fob Replacement:1. Insert first original working key into the ignition and turn ignition switch to ON. Wait for approximately 3 seconds then turnignition to OFF and remove key.2. Within 15 seconds of removing first key insert second original working key into ignition and turn ignition switch to ON. Wait approximately 10 seconds. You will see the immobilizer warning lamp illuminate on the dash and you will hear an audible tone.Turn ignition OFF and remove the key.3. Within 50 seconds insert the new unprogrammed key into ignition. Turn ignition switch to ON. After approximately 10 seconds you should hear an audible tone and the immobilizer lamp will remain illuminated for 3 seconds. Once this occurs programming iscompleted.4. For each additional key you must repeat these steps starting with step number 1.Step-By-Step How To Programming InstructionsPrepare VehicleENTER Vehicle and CLOSE all doors.Enter Programming Mode – Step 1INSERT a working remote head key into the Ignition and TURN it to the ON/RUN position.Enter Programming Mode – Step 2PRESS and HOLD the UNLOCK button on the working remote head key for 4-10 seconds.Enter Programming Mode – Step 3WHILE holding the UNLOCK button, PRESS the PANIC button until a chime sounds to indicate successful entry into Programming Mode.Release ButtonsRELEASE BOTH the PANIC and UNLOCK buttons.Press ButtonsPRESS BOTH the LOCK and UNLOCK buttons simultaneously on the same remote head key until a chime is heard.Program RemoteOnce the chime is heard, WITHIN 30 seconds PRESS and RELEASE the UNLOCK button on that same remote. Another chime will sound indicating successful programming of that remote.Program Additional RemoteWITHIN 30 seconds, REPEAT Step 7 for ALL remotes (even working remote head keys) that you want to work with your vehicle.Exit Programming ModeTURN Ignition to OFF/LOCK and REMOVE key to EXIT Programming Mode.Test RemotesTEST all remotes. Programming is complete.

Took these to Ace Hardware to have cut. Followed the instructions in the manual and online to program them. Requires both OEM keys to program a new one but only takes a couple minutes to do both.Great value, same as factory best I can tell. Would buy again and recommend.

No problem with programming them for my 2005 Jeep Grand Cherokee. The seem to be good quality.

I took a chance on these blank keys for my Jeep. (The ones I bought from Ebay did not work.). These keys worked perfectly. Had I gone to the dealer it would have cost me about $300. With these keys, I save a lot.

I only had one key for my car after buying it used. The key fob portion was working sporadically when I pushed the buttons even after replacing the battery.I have a diagnostic scan tool that has the function to create keys for my vehicle. I got the keys cut at Home Depot by a helpful employee. I was told they don’t cut them there so it may or not work for you.Once I got home I connected my scan tool and went to program the key only to learn that the vehicle has a PIN number that is required for the key to be programmed to the vehicle.Once at the Dodge dealer I only needed my vehicle registration and ID to get the code. No cost.With this information I programmed my two new keys in only a few minutes. The keys work like new with awesome range. Very pleased with my purchase, thank you

Bought these keys for my son's Jeep Commander. Took them to a locksmith so that he could program the keys. Took him 15 minutes and keys work fine.

The items worked..just like the originals.. the website has misinformation make sure you buy the ones that look addintacle to the old ones .. look in the back of the originals they have serial # make sure they match other than that you good .to program go in YouTube.. great product

Locksmith was able to grind and program the keys in less than 10 minutes!!

continuamente se abre en dos partes la carcaza. fuera eso bien

Followed the instructions included with the Remotes and took them to a locksmith to help code. Great solution as the dealership wanted over $200 for one!

The keys would not sync. I tried for over an hour after I had the keys cut. I followed the directions to the letter. I even tried changing the batteries and using other internet references to make sure I was doing everything right. Waste of money.

Price

Worked flawlessly. Super happy