Thermalright HR10 2280 PRO SSD Cooler, Double Sided Heatsink, Carries 14.8W/m.k Silicone Pad, Includes 4 heatpipes, Reflow Process, 2280 SSD Heatsink Cooler for Desktop

Excellent M.2 SSD cooler. Very reasonably priced. Incredibly effective at lowering SSD temps. Nothing over 54C under heavy load. Superb!

This cooler works great! The high speed pwm fan is basically silent. Keeps my drive running way below thermal throttling temps. The price is nice too!

Does a great job keeping my WD SN850X cool. Much better than stock motherboard heatsink. The Thermalright is a tight fit between the graphics card and dual tower air cooler (Thermalright Royal Pretor 130). Can not hear the fan at 100%. Fan is replaceable if/when it fails. I did buy some thicker thermal pads (1.5mm) to replace stock ones that look to be 1mm. The stock pads are too thin and have poor thermal conductivity. Much better temps with using Gelid Ultimate 1.5mm. Installation was not too difficult (my first time). Make sure to get good pressure when you sandwich the SSD and take your time tightening the screws, each a little at a time.

I have a 5 yrs old SSD and it gets overheated very often, after I installed this heat sink no more heaving issues at all

So i knew going with the Gen5 SSD would require lot of thermal cooling solutions because it runs super hot, so even tho my motherboard comes with a large and long passive heat sink, I order 2 thermalright ssd active heatsink, one small black and then this large silver one. I first tried it with my stock motherboard heat sink and the results was that i get 8000mb/s then I switch to this large thermalright active heatsink then my writing and reading speed went back to 12,000mb/s the temperture also was night and day, with the motherboard headsink it was 140+ degree, but with this heatsink the max it goes to is 104, but stays around 98-100 degree instead it truely is a solution to the heating problem that a gen5 ssd has.

I had the Thermalright HR10 2280 PRO SSD Cooler in My box for 1 year and this unit is still kicking Everything is as cool as could be and can't even hear the thing running I've Ran some video editing Programs thru and still running verry cool I highly recommend! Also you don't break the bank with this one. If you need A memory cooler this one is the bomb!!!!

Recently I upgraded my gaming PC from the ground up. New motherboard, CPU, memory, and NVME. I went with AM5 and since MB supported Gen 5 NVME, I went with a Crucial T700 1TB drive. Install went smooth with no hitches but I immediately noticed that the NVME SSD was running extremely hot. I had read how hot these new gen5 drives get, but I was amazed at the temps. While gaming, the drive would get to 160 degrees (F) and while just sitting idle it was at 136 degrees. The MB heatsink was not doing a very good job. I read and researched on SSD heatsinks and decided on the Thermalright HR10. I was skeptical at first but when I installed it on my SSD I was completely amazed. My idle temps had gone down to 105 degrees and while gaming it only reached 126 degrees. What a difference. I highly recommend this product as it has done well in reviews and is so low priced. It will make a difference.

The product works great, WITH CORRECT PADS. I’m using five Gen 4 NVMe m.2 drives, THREE Crucial P3 Plus and TWO Samsung 990Pros. The P3 plus isn’t super hot to begin with but still hits 80C+ easily, the Samsungs are HOT and regularly hit 90C+. This cooler drops the temps by 20-25C, after changing the pads to the correct thickness. I do a lot of video editing, some gaming and would typically see my drives running at 80-90C+ with regular heat sinks. They’re all rated at 70C before throttling…. The stock thermal pad these come with is WAY too thin and does not touch all of the chips on the drive. I replaced the thermal pads with 1.5mm GElid Ultimate pads (brand isn’t as important, thickness IS important). With the 1.5mm thermal pads the cooling is substantially better dropping on average 20C because it’s actually touching all of the chips. I control the fan speed with Fan Control software and at 100% they rip at 8000+ RPM!!! They RIIPPP!!! Under normal conditions the fans at 30% is absolutely enough. Under heavy workloads and gaming the M.2 directly above the GPU (typically the OS/program drive) WILL get hotter than the rest so with the fans at 100% at 60C they stay nice and cool. This particular drive is the one monitored in Fan Control and m.2 fans speeds are set based on this drive. Under heavy workloads with a regular heatsink 80-90C+ and with this Thermalright fan heatsink the temp runs at 60C MAX! I work A LOT using my pc (video editing) and play some games and this keeps my drives running at full speed ALL the time. Because of the thermal pad being too thin, 4 stars. Definitely would recommend this product for GEN4 & GEN5 drives, just change out the thermal pads it comes with to1.5mm pads touching the chips and controller. Be sure to compress the pad/plates to where they all touch and tighten the screws while keeping pressure on the plates.

It would be good if the length can be made shorter by few mm so that it will not block the screw hole. The width should be also made a bit smaller (perhaps by 0.1 or 0.5mm) so that it will not fit too close and touch other component in the motherboard.

SSD'ler için soğutma performansı güzel ama büyük ayrıca birazda ağır , iyi bir anakartınız varsa sağlamsa olabilir. Yoksa düşünmeniz gerekiyor. SSD soğutma değerlerinde güzel sonuçları var. Fiyatının hakkını veriyor

can dissipate heat from samsung 980 pro gen4. if it fits your board get this one. i wish they put copper tubing to get more heat out but from temp reduction i got it really great. now 37-40 Celsius

ممتازه سابقا الهارديسك كان حرارته توصل لين 60 و 70 بعد تركيب الهيتسينك دا انخفضت الحرارة الى 50و 45 في الوضع الطبيعي واللعب ♥️

Reduced temps on my nvme by 15-20 degrees celcius